Wayne DW-10 Operation Manuals Download Page 17

   

 

 

 

Cautions: 

 

Do not use the printer under conditions where the printer ventilation holes are blocked, where 
any  object is placed on the printer  or  where the printer is covered  or wrapped by a cloth or 
other materials. 

The printer may have an adverse effect on nearby radio or TV transmissions. 

There may also be cases when nearby electrical appliances adversely affect  the printer, 
causing data errors or malfunction. 

Avoid using the printer near a radio or TV set  or supplying it from the same outlet as these 
appliances. 

Avoid using the printer interconnected with a cable or cord that has no protection against 
noise. 

Avoid using the printer with a device that is a strong source of noise. 
Use the printer with its grounding post connected to an appropriate grounding facility. 

Before connecting or disconnecting the grounding lead to or from the printer, always unplug it 
from supply outlet. 

If leakage occurs electric shock may result. 

Do not connect the grounding post onto any of the following facilities: 

  Utility gas piping. (A gas explosion could result.) 
  Telephone line ground 
  Lighting rod 
  Utility water pipes (Plastic water pipes should not be used for grounding.) 
To prevent possible malfunction or failure, observe the following. 

    Avoid operating the printer without paper properly loaded. 

   Avoid the use of paper not complying with specifications. 

   Avoid using torn pieces of paper or spliced with plastic adhesive tapes. 

   Avoid forcibly pulling already loaded paper by hand. 

   Avoid wedging the paper in by the paper cover or others. 

   Avoid using a sharp pointed device to operate panel keys. 
Be sure to firmly insert the cable plug into its mating socket. 

A cross connection may damage the printer’s internal electronics or the host system’s   
hardware. 
To prevent injury and further printer failure, observe the following: 

    Do not touch the printing surface of the thermal head. The thermal head is at a dangerously 

high temperature immediately after printing 

    Do not touch any of moving parts (e.g., paper cutter, gears, active electrical parts) while the   

printer is working. 

 

In case of trouble, do not attempt to repair the printer. Refer to you qualified service personnel. 

 
 

 

Caution: 

When cleaning the printer, use a soft, dry cloth for cleaning the front surface of the printer door. 
For severe stains, use a soft cloth slightly dampened with water. Never use organic cleaning solvent   
such as alcohol, paint thinner, trichloroethylene, benzene, or ketone. Never use a chemically   
processed cleaning cloth. To remove paper chips, use a soft brush.

_____________________________________________________________________________________

13 

P/N 000-920921-    Rev 0D  04/2015 

 

 

 

Summary of Contents for DW-10























Reviews: