Wayne DW-10 Operation Manuals Download Page 12

 

 

2.6  Low Paper Sensor Position 

 

 
 
 
 
 
 
 
 
 
 
 

 
 
 

Position 

Paper diameter 

Length of the remaining paper 

About    23.5 

Not used 

About    28.0 

About  2 meters 

3 Default Setting 

About    33.0 

About  6 meters 

About    37.5 

About  11 meters 

 

 
The  printer  has adjustable paper near end (low paper) sensor. Set the sensor to the 
appropriate position depending of the paper roll core diameter  and the length of the 
remaining paper when you wish to be notified of the low paper. The factory setting is the 
position 3 default is the factory setting. 
 
 
 
 

3   ERROR LIGHTS AND PAPER JAMS 

3.1

 

Error Lights 

 

Below is a description of the detected  symptoms  that are listed in Table 3-1 on the following 
page: 

  Paper end: 

 

Paper empty is detected in two steps: paper end and paper near end. 

 

In either case, the ERROR lamp is lit. If paper end is detected, replace the paper roll. 

  Front door open: 

 

If the printer door is opened accidentally, the ERROR light will go on and the print will be 
continued even though the door is opened. 

  Head up: 

 

The ERROR light blinks when the Head Up lever is lowered while printing. The lever should 
be in the up position after clearing a jam. The print restarts automatically. The ERROR light 
goes to the On state if the lever is lowered. 

  Thermal head over heat: 

 

When printing  dense characters or dark images, the head temperature rises. If the head 
temperature exceeds a specified level, the printer stops printing  and waits until the head 
temperature cools off. During waiting, the ERROR light  blinks slowly. When the head 
temperature goes back to normal operating range, printing resumes automatically. 

8

____________________________________________________________________________

________

 

 

 

P/N 000-920921-    Rev 0D  04/2015 

 

Summary of Contents for DW-10























Reviews: