6
A. FLAG ANGLES (AS REQUIRED):
A1. Quick Install (Q.I.) Flag Angles
A2. Fully Adjustable (F.A.) Flag Angles
B. JAMB BRACKETS (AS REQUIRED):
B1. Quick Install (Q.I.) Jamb Brackets
B2. Fully Adjustable (F.A.) Jamb Brackets
B3. Wind Load Jamb Brackets
C. TRACK ROLLERS:
C1. Short Stem Track Rollers
D. GRADUATED END HINGES:
D1. Single Graduated End Hinges (S.E.H.), Industry Standard
D2. Single Graduated End Hinges (S.E.H.), Narrow Hinges
E. STACKED SECTIONS:
E1. Top Section
E2. Intermediate(s) Section
E3. Lock Section
E4. Bottom Section
F. TOP FIXTURE (AS REQUIRED):
F1. Top Fixture Assemblies
G. STRUT(S) (AS REQUIRED):
G1. Strut (U-shaped)
H. DRAWBAR OPERATOR BRACKET (FOR TROLLEY OPERATED DOORS):
H1. Top Halve Drawbar Operator Bracket / H2. Bottom Halve Drawbar Operator Bracket
H3. Drawbar Operator Bracket (Supplied By Others)
I. TRACKS (AS REQUIRED):
I1. Left Hand and Right Hand Horizontal Track Assembly
I2. Left Hand and Right Hand Vertical Tracks
I3. Left Hand and Right Hand Riveted Vertical Track Assembly
I4. Left Hand and Right Hand Angle Mount Vertical Track Assembly
J. TORSION SPRING ASSEMBLY (AS REQUIRED):
J1. Left Hand and Right Hand Torsion Springs (As Required)
J2. Counterbalance Lift Cables
J3. Left Hand and Right Hand End Bearing Brackets (As Required)
J4. Left Hand and Right Hand Cable Drums
J5. Center Bracket (As Required)
J6. Center Bracket Bushing (As Required)
J7. Center Bearing Bracket (As Required)
J8. Torsion Shaft / Torsion Keyed Shaft (As Required)
J9. Torsion Keyed Shafts (As Required)
J10. Keys (As Required)
J11. Center Coupler Assembly (As Required)
K. REAR BACK HANGS:
K1. Left Hand and Right Hand Rear Back Hang Assemblies
K2. Left Hand and Right Hand Center Back Hang Assemblies
L. BOTTOM CORNER BRACKETS (AS REQUIRED):
L1. Left Hand and Right Hand Bottom Corner Brackets
M. BOTTOM WEATHER SEAL (AS REQUIRED):
M1. Bottom Weather Seal (Door Width)
B3.
B3.
F1.
A2.
A1.
A2.
B2.
B1.
B2.
A1.
C1.
E4.
E1.
E2.
E3.
I2.
I1.
I1.
I2.
K1.
K1.
J3.
J5.
J3.
J2.
J1.
J4.
J2.
J1.
J8.
I4.
I4.
B1.
I3.
I3.
C1.
J3.
J3.
J11.
J10.
J9.
J9.
J5.
J6.
J7.
J4.
NOTE:
The illustrations shown on this page are
general representations of the door parts. Each
specific door models may have unique variations.
J10.
J10.
J10.
G1.
H2.
H1.
H3.
F1.
J5.
J7.
J5.
J7.
K2.
K2.
K2.
NOTE:
For Item (K2), The Rear Center Back Hang
Assemblies are to used for all doors over 11’0” door
height and over 14’0” door width. One Rear Center
Back Hang Assembly, per side.
NOTE:
For Item (K3), The Rear Center Back Hang
Assemblies are to used for all doors over 16’0” door
height. Two Rear Center Back Hang Assemblies, per
side.
C1.
D2.
D1.
L1.
L1.
M1.
PARTS BREAKDOWN
Summary of Contents for 8700
Page 21: ......
