background image

SmartSensor 105 User Guide – Wavetronix LLC 

9/20/07

 

 

SmartSensor 105 

 

Installation Guide 

 
 

Wavetronix LLC 

380 S. Technology Ct. 

Lindon, Utah 84042 USA 

Voice:  (801) 764-0277 

Fax:  (801) 764-0208 

Web: 

www.wavetronix.com

 

E-mail: 

[email protected]

 

 
 
 
 
 
 

© 2007 Wavetronix LLC. All Rights Reserved. 

 

SmartSensor, SmartSensor Manager, Click!, Wavetronix, and all associated logos are trademarks of Wavetronix LLC.  All other 

product or brand names as they appear are trademarks or registered trademarks of their respective holders.   

 

Protected by U.S. Patent Nos. 6,556,916 and 6,693,557.  Other U.S. and international patents pending. 

 

The Company shall not be liable for any errors contained herein or for any damages arising out of or related to this document or the 

information contained therein, even if the Company has been advised of the possibility of such damages. 

 

This document is intended for informational and instructional purposes only.  The Company reserves the right to make changes in the 

specifications and other information contained in this document without prior notification. 

 

Summary of Contents for SMARTSENSOR 105





































Reviews: