Massage
bathtub
Massage
bathtub
Page
8
of
11
Page
3
of
11
6. 7 Pl ea se che ck wh et he r the re is fal l off or br ea kag e on wi re, swi tch, con ne ctor pl ug s so tha t rep ai r
in time.
6. 8 In or de r to kee p to us e in a lon g ter m ,pl ea se reme mbe r, do n' t us e mor e tha n 3 ho ur s con tinu el y.
7
、
Fault eliminate
Remark: except this fault, please according to situation to resolve, or find
experienced people to repair.
8
、
special remind
8.1 please find qualified people to install bathtub according to introduction.
8.2 when you are using it, first of all you have to inject the cold water and then inject the
hot water. Don't inject the hot water first.
2
8.3 bathtub's machine must connect on ground, support must use 1.5mm yellow/green
double wire connect with ground and check whether effective.
8.4 please do not turn on machine without water, before draining should turn off machine.
8.5 children should be looked after in bathtub.
8.6 bathtub's temperature cann't higher than people average temperature, and the best
is 32-37centigrade.
8.7 after shower ,please cut off power.
8.8 if have these situation ,please do not enter into massage bathtub.
8.8.1 younger than 4 years old's child;
8.8.2 blood circulation unstabled people;
8.8.3 sot;
8.8.4 suffer from flu;
8.8.5 heart disease;
8.8.6 already have sauna;
8.8.7 after meal in half a hour;
Remark: our company has the right to modify the above mention without further notice.
Check circuitry
Insert again or change
power line
Connect again or change
Change
Connect with supplier
Fix tightly again
Adjust
Way
Change
Fix again
Change
Voltage unstable
Power connector didn't connect
well or open circuit
The windpipe connect air switch
fall off or break
Cause
Power's parameter is not same as
nameplate
Fixed screw did'n fix or fall off
Support's leg screw did not touch
ground
The joint did not fix well
Water pipe or accessory leak
Aging
Machine or equipment
doesn't work
water pipe leak out
Big nose of machine
Fault
The air switch failure
6.Waterfall&whirlpool
6.1 The water checking device of this controller protects the water
pump from burning out.
6.2 While the water level achieves the setting value , press“ ”
to start the Waterfall&whirlpool function and the icon blinks on the LCD
press again, Waterfall&Water pump surf is stopped.
6.3 When the water level lowers than the setting value, pump stops working.
6.4 When the Waterfall&whirlpool function is on, and the system checks
the water level lower than the setting value, Waterfall&whirlpool
function stops automatically, at the same time the pump icon blinks.
When anytime the system checks the water level achieves the setting
value, the icon stops blink and the pump starts to work.
Special alert
：
When turn on the function of whirlpool massage and
waterfall massage, press
（
）
can turn on the electrical water
volume adjustment function. Let both massages power keep changing
from maximum to minimum then maximum. When the waterfall volume
is at is maximum, then the jets are in weakest power, vice versa. Press
（
）
again can stop changing.
(optional function)
；
7.FM Radio
7.1 The FM frequency scope is 87.5MHz—108.0MHz.
7.2When the system is on, press the button “ ” to turn on the
FM Radio Function, at the same time, the LCD displays the current
frequency and “FM” “MHZ”
press the icon “ ”again ,FM
function stops while the current frequency and “FM” disappears.
7.3 When the FM function is on, press “ ” till the LCD blinks
“FM” and “MHZ”, the system enter into the state of adjusting the
frequency.
7.3.1press “ ”to increase the length of one step (the length of
one step =100KHz): Press this button over 2 seconds, the system
searches the radio stations of larger frequencies automatically; the
digital phase locked loop will lock the FM station automatically and
the LCD shows the present frequency, when it reaches to the limit of
108.0MHz, press this button again and the frequency jumps to 87.5
Mhz.
.
；
