wattstopper RD‑250 Installation Instructions Manual Download Page 8

Page: 8 / 8

• The time delay can be set from 15 seconds to 30 minutes. Check the time

delay setting for each RD‑250 in your multi‑way configuration. Ensure that all

RD‑250s have the same time delay setting. Ensure that there is no movement

within any of the sensors’ view for the set time period. Hot air currents and

heat radiant devices can cause false detection. Make sure the sensor is at least

6 feet (2 meters) away from devices that are a significant heat source (e.g.,

heater, heater vent, high wattage light bulb).

If load does not respond properly after following troubleshooting, turn OFF

power to the circuit then check wire connections or call technical support.

COVER PLATES

WattStopper RD wall switches fit behind industry standard decorator style switch

cover plates.

WARRANTY INFORMATION

WattStopper warranties its products to be free of defects in materials

and workmanship for a period of five (5) years. There are no obligations

or liabilities on the part of WattStopper for consequential damages

arising out of, or in connection with, the use or performance of this

product or other indirect damages with respect to loss of property,

revenue or profit, or cost of removal, installation or reinstallation.

Please

Recycle

2800 De La Cruz Boulevard, Santa Clara, CA 95050

Technic

al Support: 800.879.8585 • www.watt

stopper.com

2800 De La Cruz Boulevard, Santa Clara, CA 95050

800.879.8585 • www.wattstopper.com

08703r3 3/2013

Please

Recycle

Summary of Contents for RD‑250









Search results

Summary of Contents for RD‑250

Reviews:

Related manuals for RD‑250

Brands by name

Popular brands

wattstopper RD‑250, Installation Instructions Manual

Search results

Summary of Contents for RD‑250

Reviews:

Related manuals for RD‑250

Brands by name

Popular brands