Wattsense Box V1.2 Installation Manual Download | Manualshive

Page: 20 / 25

background image

Box Wattsense - Installation Guide

18 / 23

• Make sure to have an Ethernet switch.

• Connect the power supply to the switch.

• Connect an Ethernet cable to the Ethernet port ETH1 or ETH2 of the Box.

• Connect the other end of this cable to the Ethernet switch.

• Check that the ETH1 or ETH2 LED lights up.

• Connect all equipment to the switch via the Ethernet cables.

«
...
18
19
20
21
22
...
»

Summary of Contents for Box V1.2


























Reviews:

No comments

Related manuals for Box V1.2

Brand: FOLKSAFE Pages: 6

TrauTech TSH314-HD

Brand: Charmex Pages: 2

Brand: Philips Pages: 2

Brand: Agilent Technologies Pages: 7

SYSTIMAX 360 iPatch PATCHMAX

Brand: CommScope Pages: 6

Brand: Micro Rain Pages: 29

Brand: Lindy Pages: 2

Brand: RocketFish Pages: 2

SSII ADVANCED RPS Y CABLE TYPE 3

Brand: 3Com Pages: 4

Uniqua 1 Series

Brand: Hardy Pages: 2

Brand: AV Access Pages: 16

Brand: IAdea Pages: 11

Brand: cable matters Pages: 4

Brand: I-PEX Pages: 22

Brand: National Instruments Pages: 2

20613-0 E-0 Series

Brand: I-PEX Pages: 12

Brand: Philips Pages: 2

Brand: Wayne-Dalton Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands