background image

IOM-WQ-PWR2511   1802 

EDP# 2915862 

© 2018 Watts

USA:  

North Andover, MA • Tel. (800) 224-1299 • www.watts.com 

Canada: 

Burlington, ON • Tel. (888) 208-8927 • www.wattscanada.ca

LIMITED WARRANTY:

  Certain Watts Pure Water products come with a limited warranty from Watts Regulator Co.  Other products may have no warranty or are covered by the original manufacturer’s  

warranty only.  For specific product warranty information, please visit www.watts.com or the published literature that comes with your product.  Any remedies stated in such warranties are exclusive and 

are the only remedies for breach of warranty.  

EXCEPT FOR THE APPLICABLE PRODUCT WARRANTY, IF ANY, WATTS MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. TO THE FULLEST EXTENT 

PERMITTED BY APPLICABLE LAW, WATTS HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND IN NO EVENT SHALL WATTS BE LIABLE, IN CONTRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THEORY, FOR 

INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR PROPERTY DAMAGE, REGARDLESS OF WHETHER IT WAS INFORMED ABOUT 

THE POSSIBILITY OF SUCH DAMAGES. 

Summary of Contents for PWR2511 Series









Reviews: