Watts PVI AQS-14 Installation Manual Download Page 7

Page: 7 / 16

STEP BY STEP GUIDE TO PLUMBING

THE SOFTENER

(CONTINUED)

Please Remember

–

Only use tablet or pellet salt in your softener!

CONNECT TRANSFORMER

1. Connect the power cable leads to the two terminals on the

transformer.

NOTE:

Check to be sure all lead wire connections are secure on the

back of the faceplate.

CAUTION:

Be sure all wiring is away from the valve gear and motor

area, which rotates during recharges.

2. Plug the transformer into a house electrical outlet.

THE UNIT WORKS ON 24V ONLY. DO NOT CONNECT WITHOUT
THE TRANSFORMER.

STEP BY STEP GUIDE TO PLUMBING

THE SOFTENER

(CONTINUED)

CONNECT TRANSFORMER

1. Connect the power cable leads to the two terminals on the

transformer.

NOTE:

Check to be sure all lead wire connections are secure on the

back of the faceplate.

CAUTION:

Be sure all wiring is away from the valve gear and motor

area, which rotates during recharges.

2. Plug the transformer into a house electrical outlet.

THE UNIT WORKS ON 24V ONLY. DO NOT CONNECT WITHOUT
THE TRANSFORMER.

Please Remember

– Only use tablet or pellet salt in your softener!

Summary of Contents for PVI AQS-14

















Search results

Summary of Contents for PVI AQS-14

Reviews:

Related manuals for PVI AQS-14

Brands by name

Popular brands

Watts PVI AQS-14, Installation Manual

Search results

Summary of Contents for PVI AQS-14

Reviews:

Related manuals for PVI AQS-14

Brands by name

Popular brands