background image

3

Equipment Specifications

Watts OneFlow

®

 systems are complete, self-contained, loaded 

with media and ready to use. A simple inlet and outlet connec-

tion is all that is required for installation. Please review operat-

ing pressures, temperatures and water chemistry limitations to 

ensure compatibility and performance.

**Copper

Pursuant to the EPA drinking water standards, the copper con-

centration permitted is up to 1.3 ppm. Typically originating from 

new copper plumbing, high levels of copper can foul OneFlow 

media. For applications with copper concentration greater than 

1.3 ppm, please contact Watts Pure Water Technical Service at 

1-800-224-1299. To further minimize any problem with excess 

copper, avoid applying excessive flux on the inner surfaces 

of the pipe and use a low-corrosivity water soluble flux listed 

under the ASTM B813 standard.

NOTICE

***Silica

OneFlow

®

 media does not reduce silica scaling. While silica tends 

to have a less significant effect on scale formation than other 

minerals, it can act as a binder that makes water spots and scale 

residue outside the plumbing system difficult to remove. This 20 

ppm limitation is for aesthetic purposes.

a

b

c

Mechanical Specifications

Model

835

935

1035

Max Service Flow 
(gpm)

8

12

16

Dry Weight (lbs)

19

23

25

 

 

 
 
 

a

40

40

40

b

37

37

37

c

12

12.5

13

Using OneFlow

®

 with other water treatment 

chemicals

The addition of soaps, chemicals, or cleaners, before or after 

OneFlow treatment, may reverse its anti-scale treatment effects 

and/or create water with a heavy residue or spotting potential. 

Any adverse conditions caused by the addition of soaps, chemi-

cals, or cleaners are the sole responsibility of the end user.

Figure 2.

pH

6.5-8.5

Hardness (maximum)

25 grains (427 ppm CaCO3)

Water Pressure

15 psi to 100 psi (1.03 bar to 6.9 bar)

Temperature

40° F to 100° F (5°C to 38°C)

Free Chlorine

<2 ppm

Iron (maximum)

0.3 ppm

Manganese (maximum)

0.05 ppm

Copper

1.3 ppm*

Oil & H2S

Must be Removed Prior to OneFlow

Silca (maximum)

20 ppm**

*  

See note about iron, manganese and copper on the next 

page.

**  These systems prevent hardness related scale formation inside 

the plumbing system of the home at influent hardness levels of 

25 grains per gallon of calcium carbonate and less. Due to vari-

ances in water chemistry certain aesthetic conditions external 

of the plumbing system may not be attained.

WARNING

!

NOTICE

   

Pressure drop at peak flow rate is less than 5 psi.
Pressure drop reading taken with inlet and outlet gauges installed 

at a common elevation and 80 degree feed water.

Dimensions

 (nominal - inches) 

Feed Water Chemistry Requirements

Summary of Contents for OneFlow OFRES-0835









Reviews: