background image

22

WARNING

!

Installation Precautions

•   Do 

NOT

 install system on line pressure above 90psi.

•   Do 

NOT

 install system on HOT water line. Failure to limit line 

temperature to 100°F/37.8°C may result in housing failure 

and damage.

•   Do 

NOT

 install the system backwards with the feed water 

line connected to the outlet.

•   Do 

NOT

 use liquid pipe compounds for fitting connections. 

USE two to three wraps of Teflon

®

 tape.

•   Do 

NOT

 solder plumbing connections attached to filter 

housing or inlet valve. Inlet valve and filter housing will be 

damaged by high temperature.

•   Do 

NOT

 allow system to freeze. Turn off water supply to 

housing and drain housing if temperature falls below 32°F.

•   Do 

NOT

 install system in direct sunlight or where system is 

exposed to harsh chemicals or may be subjected to being 

struck by moving equipment, carts, mops or any other item 

that may cause damage.

• 

 ALLOW

 a minimum of 3" under the housing to allow for 

filter replacement.

•  IF water hammer is evident, install water hammer arrestors 

before the OneFlow unit. 

•   Do 

NOT

 overtighten fitting connections into inlet valve or 

housing outlet. 

•  Always back-up valves and fittings with a wrench when installing 

a fitting to avoid turning the valve.

•   Do 

NOT

 install the unit behind equipment where it may be  

difficult to access the system for filter replacement.

Position the OneFlow unit in a suitable location. The direction 

of flow through the OneFlow unit is always left to right; keep 

this in mind when determining installation location. Do NOT 

mount the OneFlow system near any source of heat. Also, do 

not mount the system above any device or area that would be 

adversely affected by water. 

NOTICE

Not for use on closed loop systems.
  *  Systems using OneFlow cartridge technology are effective 

at controlling lime-scale formation inside the plumbing sys-

tem at influent hardness levels up to 30 grains per gallon 

(513 ppm) as calcium carbonate. Due to variances in water 

chemistry, 30 grains per gallon is a recommended hardness 

maximum due to potential aesthetic issues related to soft 

scale residue formation outside of the plumbing system. 

Testing should be performed to determine proper application 

where hardness levels exceed 30 grains per gallon.

  ** Just as with conventional water softening media, OneFlow 

media needs to be protected from excess levels of certain 

metals that can easily coat the active surface, reducing its 

effectiveness over time. Public water supplies rarely, if ever, 

present a problem, but if the water supply is from a private 

well, confirm that the levels of iron (Fe) and manganese (Mn) 

are less than 0.3 mg/L and 0.05 mg/L, respectively.

*** Pursuant to the EPA drinking water standards, the copper 

concentration permitted is up to 1.3 ppm. Typically origi-

nating from new copper plumbing, high levels of copper 

can foul OneFlow media. New Copper lines need to be 

passivated for a minimum of 4 weeks before placing unit 

into service. For applications with copper concentration 

greater than 1.3 ppm, please consult Watts Water Quality 

Technical Service. To further minimize any problem with 

excess copper, avoid applying excessive flux on the inner 

surfaces of the pipe and use a low-corrosivity water  

soluble flux listed under the ASTM B813 standard.

 

NOTICE

  OneFlow media does not reduce silica scaling. While silica 

tends to have a less significant effect on scale formation than 

other minerals, it can act as a binder that makes water spots 

and scale residue outside the plumbing system difficult to 

remove. This 20 ppm limitation is for aesthetic purposes.

††

  All other contaminants must meet the requirements of the 

USEPA Safe Drinking Water Act. Specific Mineral and Metal 

MCL’s, identified in Watts published Feed Water Chemistry 

Requirements, supersedes the USEPA SDWA.

Water known to have heavy loads of dirt and debris may 

require pre-filtration prior to OneFlow.

WARNING

!

 

 

Feed Water Chemistry Requirements

pH

6.5-8.5

Hardness (maximum)

30 grains (513 ppm CaCO3) *

Water Pressure

15psi to 90psi (1.03 bar to 6.2 bar)

Temperature

40°F to 100°F (5°C to 38°C)

Free Chlorine

<2 ppm

Iron (maximum)

0.3 ppm **

Manganese (maximum)

0.05 ppm **

Copper (maximum)

1.3 ppm***

Oil & H2S

Must be Removed Prior to OneFlow

Total Phosphates

<3.0 ppm

Silica (maximum)

20 ppm 

TDS

<1500 mg/L 

††

OneFlow systems are complete, self-contained, loaded with 

media, and ready to use. A simple inlet and outlet connection is 

all that is required for installation. Please review operating pres-

sures, temperatures and water chemistry limitations to ensure 

compatibility.

•  Connect system to cold water supply only. Water temperature 

cannot exceed 100°F/37.8°C.

•  System 

must be

 installed in a vertical, upright and level position.

•  Do not apply any other antiscalants before or after OneFlow.

WARNING

!

Summary of Contents for OneFlow OF120-2

























Reviews: