background image

IS-HF-M100+-29293  Rev 4

 

2

 

Attention Owners and Users

Thank you for purchasing the M100+™ turbidimeter. This equipment will provide safe and productive operation as long as it is installed, used, 

maintained, and serviced in accordance with the instructions in this manual and is properly maintained. Importantly, unless the user is adequately 

trained and supervised, there is a possibility of a personal injury, property damage or damage to the equipment.
Owners and users of this equipment bear the responsibility to make certain that this equipment is used properly and safely. READ THIS MANUAL 

carefully, learn how to use and service this equipment correctly, and strictly follow all of the instructions contained in this manual and the 

requirements of local, state and federal law. Failure to do so could result in personal injury, property damage or damage to the equipment. This 

manual should be considered a permanent part of your machine and should be kept available for easy reference by any user.
Owners should not permit anyone to touch this equipment unless they are over 18 years of age, are adequately trained and supervised, and have 

read and understood this manual. Owners should also ensure that no unauthorized personnel comes in contact with this equipment.
If this equipment, or any of its parts, becomes damaged or needs repair, stop using the equipment and contact an experienced service individual 

immediately. If the warning labels or this manual are misplaced, damaged or illegible, or if you require additional copies, please contact customer 

service at +1-239-337-2116 or 888-203-7248 for these items at no charge.
Please remember that this manual and the warning labels do not replace the need to be alert, to properly train and supervise users, and to use 

common sense when using this equipment. 
If you are ever uncertain about a particular task or the proper method of operating this equipment, ask your supervisor, consult this manual, access 

www.wattswater.com, or contact customer service.

Product Identification

Please record your product’s identification and purchase information which will help in the event you have questions or need any service.

Model:

Date of Purchase:

Serial #:

Seller Name/Address:

Summary of Contents for M100+ 28060













Reviews: