background image

STEP 6

Slowly open downstream isolation valve to establish flow through 
the system.

STEP 7

With a demand for flow on the system, the valve can now be ad-
justed for the proper flow rate. This requires a meter to

 

read the 

flow that the valve is providing.

STEP 8

While reading the meter register, adjust the Rate of Flow Control:

Turn the adjustment screw IN, clockwise, to increase the flow rate 

regulated (See Figure 2A).

Turn the adjustment screw OUT, counterclockwise, to reduce or 
lower the flow rate regulated (See Figure 2B).

Setting the Rate-of-Flow Control Pilot 

Counterclockwise to REDUCE  

Flow Rate Limit

Clockwise to INCREASE 

Flow Rate Limit

2A

2B

STEP 9

Opening Speed Flow Control Adjustment: The Opening speed 
flow control allows free flow into the cover and restricted

 

flow out 

of the cover of the main valve. 

If valve opening is too slow, turn the adjustment screw OUT, 
counterclockwise, increasing the rate of opening (See Figure 3B).

If valve opening is too quick, turn the adjustment screw IN, clock-
wise, decreasing the rate of opening (See Figure 3A).

STEP 10

Closing Speed Needle Valve Adjustment: The closing speed nee-
dle valve regulates fluid pressure into the main valve cover cham-
ber, controlling the valve closing speed.

If the valve closes too slowly, turn the adjustment screw OUT, 
counterclockwise, increasing the rate of closing.

STEP 11

Actuate the solenoid to close the main valve, checking that the 
main valve closes.

Counterclockwise to INCREASE 

the rate of opening

Clockwise to DECREASE 

rate of opening

3A

3B

Figure 3 

Flow Control

Figure 2 

CP14-1 Rate-of-Flow Control Pilot

4          IOM-ACV-114-1_6114-1 2115 

EDP# 1917071 

© 2021 Watts

IOM-ACV-114-1_6114-1 2115 

EDP# 1917071 

© 2021 Watts         5

Summary of Contents for LFM114-1













Reviews: