background image

6

Testing

All mechanical devices should be inspected on a regular basis to 

ensure proper functioning. The assembly should be tested at the 

time of initial installation, after servicing or maintenance, and at least 

annually thereafter. Acceptable test procedures are published by 

Foundation for Cross-Connection Control and Hydraulic Research at 

the University of Southern California (USC), American Water Works 

Association (AWWA), American Society of Sanitary Engineering 

(ASSE Series 5000), and Canadian Standards Association (CAN/

CSA B64.10). Consult the local regulatory authority for specific 

information.

Air Gap Drain

1. Before installation, check local codes. This type of drain may not 

be approved for use in some areas.

CAUTION

!

This drain is intended to catch moderate relief valve 

discharges due to line pressure fluctuations and minor 

check valve fouling. Under certain conditions relief valves 

can discharge water at rates greater than the air gap drain 

capacity.

2. For an indoor installation, locate the assembly near a floor drain 

sized to adequately handle discharge. A strainer before the 

backflow assembly is strongly suggested.

3. After installation of backflow assembly and piping, attach the 

drain funnel to the relief valve as shown in the illustration by using 

the self-tapping screws provided in the kit to join the drain funnel 

halves together, making sure the slots in the drain funnel align with 

the tabs on the relief valve port.
If the flood sensor is in use, attach the air gap directly to the 

sensor. For valve sizes ½" to 1", use air gap 909AGA (ordering 

code 0881399). For valve sizes 1¼" to 2", use air gap 909AGC 

(ordering code 0881376).

 

NOTICE

The discharge of the drain funnel is a slip-fit design. The drain funnel 

is not designed or able to support drainpipe weight.

 

VALVE SIZE 

PLASTIC

PART NO.

METAL

PART NO.

1

/

2

"

905358 

905532

3

/

4

"

905358 

905532

1"

905358 

905532

1

1

/

4

"

905359 

905533

1

1

/

2

"

905359 

905533

2"

905359 

905533

Summary of Contents for FEBCO 860 Series













Reviews: