background image

PA5

Pressure switch for
pumps and autoclaves
with adjustment range
from 1 to 5 bar.

0402202     1/4”   250V 

single phase

0402105     1/4”   500V 

three phase

Part No.      Size            Power

PA12

Pressure switch for
pumps and autoclaves
with adjustment range
from 2 to 12 bar.

0402206     1/4”   250V 

single phase

0402205    1/4”   500V 

three phase

Part No.       Size            Power

The pressure switch automatically controls operation of
the motor-driven pump according to given set pressures.
When the minimum set pressure is reached, the contacts
are closed, therefore the motor is started. Reaching of the
max. set pressure determines, instead, the opening of the
contacts, hence the motor is stopped.

APPLICATION AND OPERATION

Fully loosen differential adjusting nut (1). Turn range adju-
sting nut (2) until obtaining the required closing valve for
the contacts. Tighten differential adjusting nut (1) until the
required cut-off pressure is obtained.

ADJUSTMENT OF SET PRESSURE

Contact (b) - (c) is normally closed (it opens when the
set pressure is reached). Connection to earth is via
terminal (a).
View of the terminal board from above after removing the
cover:

ELECTRICAL CONNECTIONS

Product PA5, 250 V:
- conforms with European Standard EN 61058-1
- is approved by VDE, SETI, SEMKO, DEMKO, NEMKO, CSA. 

Product PA12, 250 V:
- is NEMKO approved

CE mark in  conformity with European Directives EEC 89/336, EEC 73/23.

APPROVALS

Overall dimensions (mm)

a

b

c

2

(a) earth terminals
(b) line terminals
(c) motor terminals

DESIGN FEATURES

Connection

1/4" F

Inner cable gland diameter

11.5 mm max. (for cables H07RN-F-3X1)

Lever mechanism

galvanized steel

Electrical contacts

brass faced with Ag-CdO

Diaphragm

NBR rubber with fabric core

Cover

high impact ABS

TECHNICAL CHARACTERISTICS

Model

PA5

PA12

Contact load rating

16(10)A

16(10)A             

a 250 V ~

a 250 V ~

Pressure setting range

1 ÷ 5 bar

2 ÷ 12 bar

Minimum differential

0,5 bar

1,5 bar

Maximum differential

2,5 bar

4 bar

Factory setting (closing)

1,4 bar

5 bar

Factory setting (opening)

2,8 bar

7 bar

Max. fluid temperature

90°C

90°C

Degree of protection

IP 44

IP 44

Summary of Contents for DOLOMIT IGD Series









Reviews: