manualshive.com logo in svg

Watts bar PMK2, Translation Of The Original Operating Manual, Page: 33 / 41

Share
Download
Watts bar PMK2 Translation Of The Original Operating Manual Download Page 33

PMK2/EMK2-IM-DE-B-EN-01-23 Rev.0

33

15.4.3  Actuator assignment

Actuator assignment for bar-agturn type GD

Thread 

„G“

DN

4 bar 

actuators

6 bar 

actuators

1/4"

10

GD-032

GD-032

3/8"

10

GD-032

GD-032

1/2"

15

GD-032

GD-032

3/4"

20

GD-052

GD-040

1/0"

25

GD-063

GD-052

5/4"

32

GD-063

GD-052

3/2"

40

GD-063

GD-063

2/0"

50

GD-075

GD-063

Tab. 13-4  Actuator assignment for bar-agturn type GD

Actuator assignment for bar-agturn type GS

Thread 

„G“

DN

4 bar 

actuators

6 bar 

actuators

1/4"

10

GS-052-06

GS-052-06

3/8"

10

GS-052-06

GS-052-06

1/2"

15

GS-052-08

GS-052-08

3/4"

20

GS-075-08

GS-063-12

1/0"

25

GS-083-07

GS-063-12

5/4"

32

GS-083-07

GS-063-12

3/2"

40

GS-092-08

GS-083-10

2/0"

50

GS-092-08

GS-083-12

Tab. 13-5  Actuator assignment for bar-agturn type GS

The detailed dimensions of the rotary actuator can be found in the supplied manufacturer 
documentation

.

Summary of Contents for bar PMK2










































Reviews:

No comments