manualshive.com logo in svg

Watts bar PMK2, Translation Of The Original Operating Manual, Page: 28 / 41

Share
Download
Watts bar PMK2 Translation Of The Original Operating Manual Download Page 28

28

PMK2/EMK2-IM-DE-B-EN-01-23 Rev.0

15.  Annex / Technical data

15.1  Technical data of rotary actuator

The technical data of the rotary actuator can be found in the supplied manufacturer docu-
mentation.

15.2  Technical data of 3/2-way ball valve of MK2 type

Standard design

Upon request

Nominal size

DN10 - DN50

Connection type

Inside thread G 3/8“ to G 2“ acc. to ISO 228-1

Mounting position

any

Nominal pressure 
rating

DN 10 – 20:  

PN 30

DN 25 – 32:  

PN 20

DN 40 – 50:  

PN 16

Operating pres-
sure

See Pressure-Temperature diagram (see Chap. 15.3)

Temperature range -20 °C - 120 °C (see Chap. 15.3)
Materials

Housing:   Forging brass, chromium-plated

Ball:  

Brass, hard chromium-plated

Switching shaft:  

Brass, nickel-plated

Sealing bowl:  

PTFE

Switching shaft seal:   PTFE+ FKM

Flow media

Neutral gases and liquids

Other media on request

Flow direction

any

Tab. 13-1  Technical data of 3/2-way ball valve of MK2 type

Summary of Contents for bar PMK2










































Reviews:

No comments