background image

Globe

Angle

Size (in)

1

 

1/4

1

 

1/2

2

21/2

3

4

6

8

10

12

14

16

20

24

A (in)

16

16

20

22

22

24

32

34

38

44

48

52

56

56

B (in)

10

10

12

14

14

16

24

26

28

30

34

40

48

48

Size (in)

1

 

1/4

1

 

1/2

2

2

 

1/2

3

4

6

8

10

12

14

16

C (in)

16

16

20

22

22

24

32

34

38

44

48

52

D (in)

10

10

12

14

14

16

24

26

28

30

34

40

Counterclockwise to OPEN 

bleed valve

STEP 1

Pre-set pilots as noted:

Pressure Sustaining –

 Turn Sustaining Control adjustment screw OUT, counterclockwise, backing pressure off the spring, to allow it to 

stay open while adjusting the other controls.

Opening and Closing Speed –

 Turn the adjustment screws on the Closing Speed and Opening Speed Controls, if the main valve is so 

equipped, OUT, counterclockwise, 11/2 to 21/2 turns from full closed position.

STEP 2

To ensure proper operation, any trapped air will need to be bled off 
the valve cover during startup. If your ACV includes a bleed valve, 
use a flat head screwdriver to slowly open the valve (See Figure 1). 

If your valve does not include a bleed valve, bleed air by loosening 
a fitting on the valve or a plug, at the highest point of the valve as-
sembly.

STEP 3

Pressure the line, by opening the upstream isolation valve slowly 
Air is vented through the air bleed valve or loosened fitting. Tighten 
the fitting when liquid begins to vent (See Figure 1).

Repeat the process until no air is trapped in the system.

Setting the Pressure Controls

The following tables detail the recommended minimum valve servicing dimensions.

          

B

          

          

FLOW

FLOW

FLOW

          

FLOW

Valve Servicing Dimensions

Figure 1 

Position Indicator

IOM-A-ACV-920-01_620-01   2115 

EDP# 1917052 

© 2021 Watts         3

Summary of Contents for Ames 920GD













Reviews: