background image

 

MFC Series Boiler Vent and Combustion Air Guide

 

 

 

    

TAG-0080_OG

  •   

GF-148-V

    •   

  3/29/2023           

Technical Support

  

  (800) 526-0288  

  Mon-Fri, 8 am - 5 pm EST           Page 14  of 

33 

 

required.  

For 

manifolded

 

ducted  combustion

,  the  total  section  length  includes  both  horizontal  and 

common vertical; individual boiler vertical connectors are included in the determination.  

EXAMPLE

: For a manifolded ducted combustion that has a 10-foot common vertical, 5-foot 

common horizontal after the last boiler and each boiler has an 8-foot vertical connector, the 
total section linear length considered is 23 feet. Because this is less than 25 linear feet, an 
attenuator is required. 

Contact  your  local  AERCO  sales  representative  for  more  information  on  the  AERCO 
exhaust muffler and air inlet attenuator.  

14.

 

Vent and Combustion Air System Design Requirements

 

The minimum exhaust vent and combustion air duct sizes for MFC Series boiler models are as 
follows: 

TABLE 3: Minimum Exhaust Vent and Combustion Air Duct Sizes 

MODEL 

MINIMUM DIAMETER 

Combustion Air Duct Diam.  

Exhaust Vent Diam. 

MFC 3000 

10 inch dia. 

10 inch dia. 

MFC 4000 

12 inch dia. 

12 inch dia. 

MFC 5000 

12 inch dia. 

12 inch dia. 

MFC 6000 

14 inch dia. 

14 inch dia. 

MFC 8000

 

16 inch dia.

 

16 inch dia.

 

MFC 10000 

16 inch dia. 

16 inch dia. 

A 1/4-

inch NPT combustion test hole is provided on each unit’s exhaust manifold connection. A 

24-inch length of straight vent is recommended downstream of the exhaust manifold.  

The vent system should always be pitched up ¼ inch per foot of run towards the vent termination 
to enable condensate to drain back to the unit for disposal. Low spots in the vent must be avoided. 
Periodic inspection should be performed to assure correct drainage.  

MFC Series vents should not be interconnected to those of other manufacturers' equipment. 

Horizontal vent and ductwork should be supported to prevent sagging, in accordance with local 
code and the vent manufacturer’s requirements. Vertical vent and ductwork should be supported 
to  prevent  excessive  stress  on  the  horizontal  runs.  The  exhaust  manifold  and  inlet  air  adapter 
should never be used as weight-supporting elements. The supports should be so arranged and 
the overall layout designed to assure that stresses on the vent and combustion air connections 
are minimized. 

The vents and combustion air ducts may be insulated in accordance with the vent manufacturer's 
instructions and local codes. 

15.

 

Condensate Removal

 

The  exhaust  vent  system  must  be  pitched  back  toward  the  MFC  Series  unit  by  a  minimum  of 
¼-inch per foot of duct length to enable condensate to drain back to the unit for disposal. Low 
spots in the vent must be avoided to prevent the condensate from collecting.  

Summary of Contents for AERCO MFC Series


































Reviews: