background image

Installation, Operation and 
Maintenance Manual

E-Treat

®

E-Treat

®

 Salt-Free Scale  

Prevention and Water Conditioning  

System
Model ETREATWCS

•  Use only lead-free solder and flux for sweat-solder connections, 

as required by state, province and federal codes.

•  Handle all components of the system with care. Do not drop, 

drag or turn components upside down.

•  Be sure the floor under the system is clean, level and strong 

enough to support the E-Treat system while in operation.

• Install the system in a protected area.
•  Do not attempt to treat water over 100°F (38°C) with the system.
•  Always connect the system to the main water supply pipe before 

the water heater.

•  Do not expose the system to freezing temperatures. Water  

freezing in the system causes equipment damage.

•  Do not install in direct sunlight. Ultraviolet rays from the sun  

may cause damage.

•  Do not use on water that is microbiologically unsafe or of  

unknown quality.

IOM-WQ-E-Treat

 

 

If you are unsure about installing your Watts E-Treat

®

 system  

contact a Watts representative or consult a professional plumber.
You are required to thoroughly read all installation instructions  

and product safety information before beginning the installation  

of this product. 

FAILURE TO COMPLY WITH PROPER  

INSTALLATION AND MAINTENANCE INSTRUCTIONS  

COULD RESULT IN PRODUCT FAILURE WHICH CAN CAUSE 

PROPERTY DAMAGE, PERSONAL INJURY AND/OR DEATH.

 

Watts is not responsible for damages resulting from improper 

installation and/or maintenance. Local building or plumbing codes 

may require modifications to the information provided. You are 

required to consult the local building and plumbing codes prior to 

installation. If this information is not consistent with local building or 

plumbing codes, the local codes should be followed.
Save manual for future reference.
Refer to the enclosed for operating parameters to ensure proper 

use with your water supply.

WARNING

!

WARNING

!

Read this Manual BEFORE using this equipment.
Failure to read and follow all safety and use information 

can result in death, serious personal injury, property 

damage, or damage to the equipment.
Keep this Manual for future reference.

E-Treat

PN # 68101336

Summary of Contents for 68101336













Reviews: