background image

   

Limited Warranty

This Reverse Osmosis System is warranted against defects in material and workmanship for a period of one year from 

the date of installation, not to exceed 1 year from the date of manufacture. Expendable items such as filter cartridges 

and membranes are not covered by this warranty.

How to obtain Warranty Service: Contact the dealer that you purchased the system from. Watts will work in conjunction 

with our dealer to repair or replace at our discretion any unit that is determined to be defective. No returns will be 

accepted with out the proper return authorization number.

What this warranty does not cover: This warranty does not cover defects resulting from improper installation, from 

abuse, misuse, misapplication, improper maintenance, neglect, alteration, accidents, casualties, fire, flood, freezing, 

environmental factors, water pressure spikes or other such acts of God.

Return shipping charges are not included in this warranty and are the responsibility of the end user.

This warranty will be void if defects occur due to failure to observe the following conditions:

1.       The Reverse Osmosis System must be hooked up to a potable municipal or well cold water supply.

2.       The hardness of the water should not exceed 10 grains per gallon, or 170 ppm.

3.       Maximum incoming iron must be less than 0.2 ppm.

4.       The pH of the water must not be lower than 2 or higher than 11

5.       The incoming water pressure must be between 40 and 100 pounds per square inch.

6.       Incoming water to the RO cannot exceed 105 degrees F (40 degrees C.)

7.       Incoming TDS/Total Dissolved Solids not to exceed 1000 ppm.

8.       Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection  

          before or after the system.

This warranty does not cover any equipment that is relocated from the site of its original installation.

This warranty does not cover any equipment that is installed or used outside the United States of America and Canada.

LIMITATIONS AND EXCLUSIONS:

WATTS  WILL  NOT  BE  RESPONSIBLE  FOR ANY  IMPLIED  WARRANTIES,  INCLUDING  THOSE  OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. WATTS WILL NOT BE RESPONSIBLE 

FOR ANY  INCIDENTAL  OR  CONSEQUENTIAL  DAMAGES,  INCLUDING WATER  DAMAGE, TRAVEL 

EXPENSE, TELEPHONE CHARGES, LOSS OF REVENUE, LOSS OF TIME, INCONVENIENCE, LOSS OF USE 

OF THE EQUIPMENT, AND DAMAGE CAUSED BY THIS EQUIPMENT AND ITS FAILURE TO FUNCTION 

PROPERLY. THIS WARRANTY  SETS  FORTH ALL  OF WATTS  RESPONSIBILITIES  REGARDING THIS 

EQUIPMENT.

OTHER CONDITIONS:

If Watts chooses to replace the equipment, it may be replace with reconditioned equipment. Parts used in repairing 

or replacing the equipment will be warranted for 90 days from the date the equipment is returned to you or for the 

remainder of the original warranty period, whichever is longer. This warranty is not assignable or transferable.

Summary of Contents for 315






















Reviews: