background image

NOTE:

1)  Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection          

     before or after the system.  

2)  This reverse osmosis system contains a replaceable component critical to the efficiency of the system. 

     Replacement of the reverse osmosis component should be with one of identical specifications, as defined by   

     the manufacturer, to assure the same efficiency and contaminant reduction performance. 

WARNING:

 Do not use this RO system appliance to purify non-drinkable sources of water that  

 

 

  are unsafe or with water of unknown quality. 

WARNING:

 Never use hot water or freeze unit. 

WARNING:

 Incorrect installation will VOID the warranty. 

12

START UP INSTRUCTIONS

If you have connected your RO system to a refrigerator / ice maker, make sure the ice maker is off (do not allow water 

to flow to the ice maker) until flushing (Step 5) is complete and the tank has been allowed to fill completely. Connection 

from the RO to the ice maker system should have an in-line valve installed before the ice maker so it can easily be closed 

to prevent water flowing to the ice maker during start up and periodic maintenance. Your RO tank must be allowed to fill 

up fully in order for the ice maker system to work properly. 

After the Tank has filled, open the RO Faucet to flush the tank completely. You will know that the tank is empty 

when the flow rate from the RO faucet is down to a trickle.  Repeat this step two more times.  The fourth tank 

can be used for drinking. This flushing process should take about 24 hours to complete.

Open the RO faucet and leave it open until water begins to trickle out (it will come out slowly).

4)

Turn on the incoming cold water at the angle stop valve.  Open the valve knob on the water feed Adapt-a-Valve 

by turning the knob counter clockwise. Check the system for leaks and tighten any fittings as necessary.   (Check 

frequently over the next 24 hours to ensure no leaks are present).

3)

2)

NOTE:

1)

Close the RO faucet allowing the storage tank to fill with water.  It may take 4 to 6 hours to fill the tank 

completely depending on the production capability of the membrane, local water temperature and water 

pressure. 

Flushing of the tank 3 times is only necessary during the initial startup and after replacing the membrane.

During the fill period you may hear water trickling due to the Reverse Osmosis Process.

NOTE

:

NOTE:

The flushing process should take about a day to complete. 

Summary of Contents for 315






















Reviews: