WattAge ULTIMATE Instructions For Final Assembly Download Page 3

3

Visit our website at http://watt-age.globalhobby.com for information on other Wattage products

This instruction manual is designed to guide you through the entire final assembly process of your new airplane in the
least amount of time possible.  Along the way you'll learn how to properly assemble your new airplane and also learn
tips that will help you in the future.  We have listed some of our recommendations below.  Please read through them
before beginning assembly.

Please read through each step before beginning

assembly.  You should find the layout very complete
and straightforward.  Our goal is to guide you through
assembly without any of the headaches and hassles
that you might expect.

There are check boxes next to each step.  After

you complete a step, check off the box.  This will help
prevent you from losing your place.

Cover your work table with brown paper or a soft

cloth, both to protect the table and to protect the parts.

Keep a couple of small bowls or jars handy to put

the small parts in after you open the accessory bags.

We're all excited to get a new airplane in the air, but

take your time.  This will ensure you build a straight,
strong and great flying airplane.

If you come across this symbol 

,  it means that

this is an important point or an assembly hint.

If you should find a part missing or damaged, or have any questions about assembly, please

contact us at the address below:

Global Services

18480 Bandilier Circle

Fountain Valley CA  92708

Phone: (714) 963-0329          Fax: (714) 964-6236           Email: [email protected]

INTRODUCTION

Thank you for purchasing the new Wattage Ultimate Bipe EP.  Before completing the final assembly of your new
airplane, please carefully read through this instruction manual in its entirety.  Doing so will ensure your success
the first time around!

Wattage Ultimate Bipe EP Special Features:

Compact Design for Exciting Small-Field Flying

One-piece built-up wings, Plywood Outer Wing Struts and Plywood Center Cabane Strut

Entire Airframe is Hand-Built from Quality Balsa & Plywood

Covered with Real Iron-On Covering Material

Preinstalled Cobalt 400 Direct Drive Motor for More Power

Prepainted Cowling, Wheel Pants & Tinted Canopy

Generous Hardware and Custom Decal Set Included - Including Durable Aluminum Main Gear

Fast & Easy Assembly - Over 40 High Resolution Digital Photos & Drawings Guide You

To serve your needs better, please include your email address with any correspondence you send to us.  Your email
address will be added to our Customer Service Database so you will automatically receive free updates and tech
notices for your particular product.  You will also receive repair status updates (if applicable) and other important
information about your product as it becomes available.

IMPORTANT INFORMATION ABOUT YOUR EMAIL ADDRESS

Global Hobby Distributors will not disclose the information it collects to outside parties.  Global Hobby Distributors does not sell,

trade, or rent your personal information to others . Your privacy is important to us.

Visit Our Website

http://globalservices.globalhobby.com

Summary of Contents for ULTIMATE

































Reviews: