manualshive.com logo in svg

Watt Stopper DT-200, Installation Instructions Manual, Page: 16 / 16

Share
Download
Watt Stopper DT-200 Installation Instructions Manual Download Page 16

WARRANTY INFORMATION

WattStopper warranties its products to be free of defects in materials and 

workmanship for a period of five (5) years. There are no obligations or liabilities 

on the part of WattStopper for consequential damages arising out of or in 

connection with the use or performance of this product or other indirect damages 

with respect to loss of property, revenue, or profit, or cost of removal, installation 

or reinstallation.

ORDERING INFORMATION

Catalog #

Description

DT-200

Dual Technology Occupancy Sensor, Low Voltage  

w/Isolated Relay

DT-205

Dual Technology Occupancy Sensor, Low Voltage

BZ-50, 150

Power Pack: 120/277VAC, 50/60Hz, 225mA with relay  

connected, 20A ballast/incandescent

B347D-P

Power Pack: 347VAC, 60Hz, 150mA. 15A ballast

S120/277/347E-P

Auxiliary Relay Pack:   120/277VAC, 60Hz, 20A Ballast 

347VAC, 60Hz, 15A Ballast

17479r3  9/2014

Please 

Recycle

2800 De La Cruz Boulevard, Santa Clara, CA 95050

800.879.8585 • www.wattstopper

.com

Please 

Recycle

2800 De La Cruz Boulevard, Santa Clara, CA 95050

800.879.8585 • www.wattstopper

.com

Summary of Contents for DT-200

















Reviews:

No comments