Watson-Marlow qdos120 User Manual Download Page 15

Page: 15 / 130

A nameplate is fixed to the rear of the pump. It contains manufacturer and contact details,
product reference number, serial number and model details.

0M0.223L.GLU

Iss 1

qdos Manual 30l/hr 7bar

190gpd 100psi Sant PFPE

Serial Number

Manufacturer details

Product reference

Model

Serial number

6.1

Pump specifications

Flow Range (flow control)

Manual, PROFIBUS, Universal and
Un:

qdos120:0.1-2000 ml/min (20000:1)

qdos60:0.1-1000 ml/min (10000:1)

qdos30:0.1-500 ml/min (5000:1)

qdos20:0.1-333 ml/min (3330:1)

Remote:

qdos120:1.25-2000 ml/min (1600:1)

qdos60:0.6-1000 ml/min (1600:1)

qdos30:0.3-500 ml/min (1600:1)

qdos20:0.2-333 ml/min (1600:1)

AC Supply voltage/frequency

~100-240V 50/60Hz

m-qdos-en-02

Summary of Contents for qdos120



































































































































Search results

Summary of Contents for qdos120

Reviews:

Related manuals for qdos120

Brands by name

Popular brands

Watson-Marlow qdos120, User Manual

Search results

Summary of Contents for qdos120

Reviews:

Related manuals for qdos120

Brands by name

Popular brands