Watson-Marlow 323Du User Manual Download Page 30

Page: 30 / 48

Watson-Marlow 323E, 323S, 323U and 323Du User Manual

E, S, U, Du

20 Drive maintenance

There are no user serviceable parts inside the pump. The unit should be re-
turned to Watson-Marlow or its appointed agents or distributors for
service.

21 Drive part numbers

Drives only

Part number

Drive type

Drive speed

Pumphead

Mains lead

type

036.3124.00U

323E

400

N/A

036.3132.00U

323S

220

N/A

036.3134.00U

323S

400

N/A

036.3142.00U

323U

220

N/A

036.3144.00U

323U

400

N/A

036.3152.00U

323Du

220

N/A

036.3154.00U

323Du

400

N/A

Complete pump assemblies

Part number

Drive type

Drive speed

Pumphead

Mains lead

type

030.3124.3DU

323E

400

313D

030.3132.RLU

323S

220

501RL

030.3134.3DU

323S

400

313DW

030.3142.RLU

323U

220

501RL

030.3144.3DU

323U

400

313DW

030.3152.RLU

323Du

220

501RL

030.3154.3DU

323Du

400

313DW

For US mains lead, replace ‘U’ with ‘A’ at end of part number.
For European mains lead, replace ‘U’ with ‘E’.

Summary of Contents for 323Du

















































Search results

Summary of Contents for 323Du

Reviews:

Related manuals for 323Du

Brands by name

Popular brands

Watson-Marlow 323Du, User Manual

Search results

Summary of Contents for 323Du

Reviews:

Related manuals for 323Du

Brands by name

Popular brands