Watson-Marlow 323Du User Manual Download Page 27

Page: 27 / 48

Watson-Marlow 323E, 323S, 323U and 323Du User Manual

RS232 settings

Baud

9600

Stop bits

Data bits

Parity

None

Flow control

None

Echo

Pump inteface
pin

Function

RX (Receive data)

TX (Transmit
data)

GND (Ground)

Reserved

RS232 command modes

These are the codes to control the pump with the RS232 serial link. They must be sent
to the pump from a computer serial port (or equivalent).

Com-
mand

Function

Com-
mand

Function

1SPxxx

Set pump speed to xxx

1RC

Reverse direction

1SI

Increase speed by 1rpm

1RR

Set clockwise direction

1SD

Reduce speed by 1rpm

1RL

Set counter-clockwise
direction

1GO

Start pump

1RS

Show all pump information

1ST

Stop pump

1ZY

Show running status of the
pump. STARTed 1 or
STOPped 0

Always terminate each command with a RETURN (ASCII CHR13).

Notes on control codes

There should be at least 10mS between commands.

The command RS to show all pump information will return the following text string:

[pump type] [speed] [CW / CCW rotation] [stopped/running, 0 /1] [! delimiter]
e.g. 323Du 110 CW 1 !

Note

: both 9 and 25-way D shells are earthed.

Summary of Contents for 323Du

















































Search results

Summary of Contents for 323Du

Reviews:

Related manuals for 323Du

Brands by name

Popular brands

Watson-Marlow 323Du, User Manual

Search results

Summary of Contents for 323Du

Reviews:

Related manuals for 323Du

Brands by name

Popular brands