Watkins C30S Owner'S Manual Download

Page: 24 / 32

Question:

Why isn’t water chemistry damage covered by the warranty?

Answer:

The chemical levels and water quality of the water in the spa are under your direct control. With proper basic care, the spa will provide many years of hot water

relaxation. If you are unsure about any chemical or its usage in the spa, contact your Authorized dealer or Watkins

Manufacturing Corporation.

WATER TERMINOLOGY

The following chemical terms are used in this Water Quality and Maintenance section. Understanding their meaning will help you to better understand the water
maintenance process.

Bromamines:

Compounds formed when bromine combines with nitrogen from body oils, urine, perspiration, etc. Unlike chloramines, bromamines have no pungent

odor and are effective sanitizers.

Bromine:

A halogen sanitizer (in the same chemical family as chlorine). Bromine is commonly used in stick, tablet, or granular form. See the DO’s and DON’Ts of Spa

Water Maintenance for additional information.

Calcium Hardness:

The amount of dissolved calcium in the spa water. This should be approximately 150-200 ppm. High levels of calcium can cause cloudy water and

scaling. Low levels can cause harm to the spa equipment.

Chloramines:

Compounds formed when chlorine combines with nitrogen from body oils, urine, perspiration, etc. Chloramines can cause eye irritation as well as having

a strong odor. Unlike bromamines, chloramines are weaker, slower sanitizers.

Chlorine:

An efficient sanitizing chemical for spas. Watkins

Manufacturing Corporation recommends the use of sodium dichlor-type granulated chlorine. This type is

preferred because it is totally soluble and nearly pH neutral.

Chlorine (or Bromine) Residual:

The amount of chlorine or bromine remaining after chlorine or bromine demand has been satisfied. The residual is, therefore, the

amount of sanitizer which is chemically available to kill bacteria, viruses and algae.

Corrosion

: The gradual wearing away of metal spa parts, usually caused by chemical action. Generally, corrosion is caused by low pH or by water with levels of TA, CH,

pH or sanitizer which are outside the recommended ranges.

DPD:

The preferred reagent used in test kits to measure the Free Available Chlorine.

Halogen:

Any one of these five elements: fluorine, chlorine, bromine, iodine, and astatine.

MPS:

Monopersulfate is a non-chlorine oxidizer.

Oxidizer:

The use of an oxidizing chemical is to prevent the buildup of contaminants, maximize sanitizer efficiency, minimize combined chlorine and improve water clarity.

Pathogen:

A microorganism such as bacterium that cause disease.

pH:

The measure of the spa water’s acidity and alkalinity. The recommended pH for the spa water is 7.4 to 7.6. Below 7.0 (considered neutral), the spa water is too

acidic and can damage the heating system. Above 7.8, the water is too alkaline and can result in cloudy water, and scale formation on the shell and heater.

ppm:

The abbreviation of “parts per million”, the standard measurement of chemical concentration in water. Identical to mg/l (milligrams per liter).

Reagent:

A chemical material in liquid, powder, or tablet form for use in chemical testing.

Sanitizer:

Sanitizers are added and maintained at recommended residuals to protect bathers against pathogenic organisms which can cause disease and infection in

spa water.

Scale:

Rough calcium-bearing deposits that can coat spa surfaces, heaters, plumbing lines and clog filters. Generally, scaling is caused by mineral content combined

with high pH. Additionally, scale forms more readily at higher water temperatures.

Shock Treatment:

Also known as “super-chlorination” when chlorine is used. Shock treatment is a process of adding significant doses of a quick dissolving sanitizer

(sodium dichlor is recommended) to oxidize non-filterable organic waste and to remove chloramines and bromamines.

Total Alkalinity:

The amount of bicarbonate, carbonates, and hydroxides present in spa water. Proper total alkalinity is important for pH control. If the TA is too high, the

pH is difficult to adjust. If the TA is too low, the pH will be difficult to hold at the proper level. The desired range of TA in spa water is 125 to 150 ppm.

WATER QUALITY AND MAINTENANCE