Watkins C30S Owner'S Manual Download

Page: 15 / 32

FILTER CYCLES

Your spa will automatically turn the filter cycle on twice each day. When the spa is first powered up the automatic filter cycle will wait 10 minutes before starting. A 1.5
hour filter cycle using the low speed of the jet pump is the programmed filter cycle time. The display will show F1 and the filter icon. The filter cycle occurs twice a day
(every 12 hours).

NOTE:

The standard Monarch

ozone system only works during the filter cycles.

To modify the length of either filter cycle:

Press and hold the “SET” button for approximately three seconds (The filtration icon will flash during programming)

Press the “LIGHT” button to select the Filter Cycle 1 or 2 (a F1 or F2 will flash in the display). NOTE: Each filer cycle needs to be set independently.

C. Using the TEMP

▲

or the TEMP

▼

button, adjust the length of filtering time desired (0 to 6 hours).

D. Programming will then be saved 10 seconds after the last button is pushed.

The filter cycle will activate the low speed of the jet pump for the entire cycle. When activated, the filter cycle icon on the display is turned on. If the temperature
exceeds the set point by three degrees F for more than three hours, the system will cancel the FILTER cycle and the filter cycle icon will blink for the remaining filter
cycle time. Should the temperature cool down to 1.5 degrees F within the set point before the end of the cycle, the cycle will resume for the rest of the time. Should you
use the spa during the filter cycle by placing the jet pump on high speed, the filter cycle icon will blink. Once the jet pump has been shut off, a ten minute tranquil mode
begins (filter cycle icon will be blinking during tranquil mode) before the filter cycle will resume. The blinking filter cycle icon indicates that the filter cycle timer is still
counting, but the cycle has been temporarily interrupted.

NOTE

: When power is lost to the spa, both the temperature setting and filter cycle, revert to the previous setting.

OPERATION NOTE:

For proper water-circulation during filtration cycles, rotate the air control valves counterclockwise to the off position.

MANUAL CLEAN CYCLE

The Manual Clean cycle operates in the following manner: Jet pump runs for ten minutes on high speed.

This system is initiated by pressing the “SET” button, then “JETS” button. The Filter and Jets icon will flash.

SLEEP MODE

The Sleep Mode operation is a feature that overrides the normal filter cycle and minimizes pump operation during evening hours. For example, if Filter Cycle 1(F1) is set
to activate at 8:00am, by default, Filter Cycle 2 (F2) will be set to activate at 8:00pm (12 hrs. later). During 8:00pm to 8:00am, if the spa should call for heat, the pump
and heater will activate to heat the spa under normal filter cycle operation. However, when in Sleep Mode, should the spa call for heat, the pump and heater will be
suspended until the activation of Filter Cycle 1 at 8:00am, to minimize pump activation during evening hours.

NOTE:

If water temperature drops below 80 degrees,

pump and heater will automatically activate to prevent temperature from dropping further.

To activate the Sleep Mode feature, press and hold “TEMP

▲

“ and “TEMP

▼

“ buttons together for 3 seconds. This will activate the feature and override the normal filter

cycle operation. When these buttons have been engaged, the Sleep Mode icon will illuminate on the control panel display, indicating the feature is active. To deactivate
this feature, simply press and hold the specific buttons in the same manner once again.

MUSIC SOUND SYSTEM (C45S AND C30S)

The C45S and C30S spas comes equipped with the music system and includes the following:

• JBL stereo

• Four Bartop Speakers

• Bartop Wire Remote

The operating instructions for the CD AM/FM Stereo have been included in the spa’s Owner’s Packet.

STEREO CONTROL PANEL MODE BUTTON

• Press “ ” to turn the stereo on and off.

• Press “BAND” button – to switch between FM1, 2, 3 and AM.

• Press “MODE” button – to source between CD/AM/FM/CD Changer.

• Press “VOL

▲