background image

DANGER

Risk of electric shock:

Install the controller at least five (5) feet (1.52m) from the inside wall of the pool and/or spa/hot tub using non-metallic plumbing. Canadian  
installations must be at least three (3) meters from the water. Children should not use spas or hot tubs without adult supervision. Do not use 
spas or hot tubs unless all suction guards are installed to prevent body and hair entrapment. People using medications and/or having an 
adverse medical history should consult a physician before using a spa or hot tub.

WARNING

To avoid injury ensure that you use this control system to control only packaged pool/spa heaters which have built-in operating and high  
limit controls to limit water temperature for pool/spa applications. This device should not be relied upon as a safety limit control.

WARNING

•  People with infectious diseases should not use a spa or hot tub.

•  To avoid injury, exercise care when entering or exiting the spa or hot tub.

•  Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconsciousness and possible drowning.

•  Before entering a spa or hot tub, measure the water temperature with an accurate thermometer.

•  Do not use a spa or hot tub immediately following strenuous exercise.

•  Prolonged immersion in a spa or hot tub may be injurious to your health.

•  Do not permit any electric appliance (such as a light, telephone, radio, or television) within five (5) feet (1.52m) of a spa or hot tub.

•  The use of alcohol, drugs or medication can greatly increase the risk of fatal hyperthermia in hot tubs and spas.

•  Water temperature in excess of 100°F (38°C) may be hazardous to your health. 

WARNING

A terminal bar marked “GROUND” is provided within the controller. To reduce the risk of electrical shock which can cause serious injury or 
death, connect this terminal bar to the grounding terminal of your electric service or supply panel with a continuous copper conductor  
having green insulation and one that is equivalent in size to the circuit conductors supplying this equipment, but no smaller than no. 12 AWG 
(3.3mm2). In addition, a second wire connector should be bonded with a no. 8 AWG (8.4mm2) copper wire to any metal ladders, water pipes, 
or other metal within five (5) feet (1.52m) of the pool/spa. In Canada the bonding wire must be minimum 6 AWG (13.3mm2). 

CAUTION

A ground-fault circuit-interrupter must be provided if this device is used to control underwater lighting fixtures. The conductors on the load  
side of the ground-fault circuit-interrupter shall not occupy conduit, boxes, or enclosures containing other conductors unless the additional 
conductors are also protected by a ground-fault circuit interrupter. Refer to local codes for complete details.

Attention Installer:

Installer to provide drainage of compartment for electrical components.

SAVE THESE INSTRUCTIONS

3

WARRANTY

For product registration visit: www.waterwayplastics.com.

For Warranty questions or claims please contact point of purchase.

Summary of Contents for Oasis 770-1004-PSW

















Reviews: