background image

Watersnake

14

RECOMMENDATIONS WHEN USING YOUR 
WATERSNAKE MOTOR IN THE WATER

Upon connecting your battery to your motor, and before setting off in your 
boat, make sure that your trolling motor is mounted correctly and stowed 
securely in the mounting bracket. Of course once you engage your Watersnake 
motor for use make sure that it is in the right place, not too low or too high. 
Once you are in deep water, you should make sure that you gradually increase 
the speed of your trolling motor, do not fl atten it up to full speed right away. 
For example, if you have a 5 speed trolling motor, don’t click through all of the 
other speeds really fast to get to 5, slowly go up to 1 speed, 2 speed, and so on. 
It is recommended not to run your trolling motor out of water for long periods 
of time.

RECOMMENDATIONS WHEN YOUR 
WATERSNAKE MOTOR IS OUT OF THE WATER

After washing down your Watersnake motor at the end of a session, you may 
need to charge your 12v deep cycle marine battery.  Before charging your 
battery, ensure that your Watersnake motor is disconnected from the battery.  
DO NOT leave your motor connected whilst charging your battery.  

If your boat is not stored under cover, it is recommended to remove your 
Watersnake motor and store separately under cover, out of direct sunlight and 
away from wet or damp areas.  If you are not able to remove your Watersnake 
from the boat, we recommend covering your Watersnake with a weatherproof 
cover to protect the electronics.

The off-season provides a good opportunity to complete some maintenance as 
outlined on page 13
When towing your boat long distances and especially if driving over rough / 
unsealed roads, we strongly recommend that you remove your Watersnake 
motor from your bow and stow safely in either your vehicle or boat.

Summary of Contents for Fierce SWRF 54/48

























Reviews: