Waters Otto SPEcialist PPM Page 49 Overview And Maintenance Manual Download

Page: 49 / 50

B Specifications

This section lists groups of individual specifications for the Otto SPEcialist PPM, as follows:

•

Physical specifications (Page 49)

•

Electrical specifications (Page 49)

•

Environmental and performance specifications (Page 50)

The reproducibility of the operating specifications presented in this document depends on the
conditions in individual laboratories. Contact the Waters Technical Service organization for
additional information about specifications (see section

Contacting Waters (Page iii)

B.1 Physical specifications

Table B–1: Otto SPEcialist PPM physical specifications

Attribute

Specification

Width

16 inches (≈406 mm)

Height

24 inches (≈609 mm)

Depth

18 inches (≈457 mm)

Weight (maximum)

65 lbs (≈29 kg)

B.2 Electrical specifications

Table B–2: Otto SPEcialist PPM electrical specifications

Attribute

Specification

Fuse

5 A, 250 V, slow-blow

Voltage

100 to 240 V, 120 W

Frequency

50 to 60 Hz

July 1, 2021, 715006867 Ver. 01

Page 49

Summary of Contents for Otto SPEcialist PPM


















































Search results

Summary of Contents for Otto SPEcialist PPM

Reviews:

Related manuals for Otto SPEcialist PPM

Brands by name

Popular brands

Waters Otto SPEcialist PPM, Overview And Maintenance Manual

Search results

Summary of Contents for Otto SPEcialist PPM

Reviews:

Related manuals for Otto SPEcialist PPM

Brands by name

Popular brands