background image

19

PREMIER 2 SINGLE-SPEED INSTALLATION AND MAINTENANCE MANUAL

4-Dehumidification/Normal. Fan speed control

This DIP switch allows field selection of the dehumidification mode, which uses the low

and medium fan speeds for cooling or the medium and high fan speeds for cooling in the

normal mode.

5-Auxiliary Off

This DIP switch disables third-stage heating. Full emergency heat would in any event still be

available if needed.

6-Diagnostics-Inputs

This DIP switch allows viewing the inputs from the thermostat to the control board such as

Y1, Y2, O, G, W, SL1-In on the LED display.

7-Diagnostics-Outputs

This DIP switch allows viewing the outputs from the control board such as compressor,

reversing valve, blower, hot water pump, and loop pump on the LED display.

8-Thermostat Selection

This DIP switch allows field selection of thermostat type connected to the Premier 2 control. If

using a TA32E12, the DIP switch must be in the ON position. The DIP switch should be in the

OFF position for 24 VAC thermostats.

FACTORY SETUP DIP SWITCHES (SW3)

A 5-position DIP switch package on the Premier 2 control allows the following factory setup

options:

1-Two-Speed/Single-Speed

This DIP switch configures the control for single-speed compressor operation or two-speed

compressor operation.

2-ECM/ECM2

This DIP switch configures the control to operate with the ECM blower motor (motor with

square control on end) or with the ECM2 (round) blower motor.

3-No RPM/RPM

This DIP switch configures the control to monitor the RPM output of an ECM/ECM2 blower

motor. When using a PSC blower motor, the control should be configured for no RPM sensing.

4-AT EH Board/Premier 2 EH Board

 This DIP switch configures the control to operate with the Premier 2 electric heat control

board (6-position connector) or with the AT electric heat control board (3-position connector).

5-Future Use

Not used at this time.

ECM2 blower motors have a 12-speed selector DIP switch on the Premier 2 logic board

(SW1) and are factory set for optimum performance. To change speeds, select the appropriate

speeds on DIP switch SW1. Refer to the blower performance table for specific airflow and

switch information.

Blower Speed

Summary of Contents for AT022C/D





























Reviews: