background image

IMPORTANT SAFETY INSTRUCTIONS

When  installing  and  using  this  electrical  equipment,  basic  safety  precautions  should  always  be 
followed, including the following:

READ AND FOLLOW ALL INSTRUCTIONS

To reduce the risk of injury, do not permit children or infirm persons to use this product unless they 
are closely supervised at all times.

RISK OF ELECTRIC SHOCK

Connect only to a grounding type receptacle protected by a ground-fault circuit-interrupter (GFCI) 
or a Residual Current Device (RCD) with a rated residual current not exceeding 30mA. Contact a 
qualified electrician if you cannot verify that the receptacle is protected by a GFCI or an RCD.

To  reduce  the  risk  of  Electric  Shock,  if  the  electrical  power  supply  cord  is  damaged  it  must  be  
replaced immediately by the manufacturer, service agent or similarly qualified person in order to 
avoid hazard.

The  power  supply  cord  should  be  located  and  protected  to  prevent  the  cord  from  sustaining 
damage from lawn mowers, hedge trimmers and other equipment. Do not bury cord.

Do not run this product on an extension cord. Damage to the electrical components may result.

Install in a well ventilated area. Do not bundle excess power supply cord near items that generate 
heat. Property damage, serious injury or death may result.

Any modification of this product requires the prior consent of the manufacturer. Original replacement 
parts and accessories authorised by the manufacturer ensure a high level of safety. The manufacturer 
accepts  no  liability  for  the  damage  and  injuries  caused  by  unauthorised  replacement  parts  and 
accessories.

WARNING

!

WARNING

!

WARNING

!

Summary of Contents for Airflo













Reviews: