background image

 

20 

 

Pumps

 - All wearing parts of the Pump that are in contact with the pumped liquid, such as rotor, 

stator, impeller, guide wheel, valves, vanes, bearings, seals etc., are not covered by this warranty. 
BW Solar Pumps are designed for pumping water potable for humans and animals, not containing 
solid or long fibred particles larger than sand grains. Max sand content: 50 g/m3, max salt content: 
300-500 ppm at max. 30° C. Defects due to pumping other liquids are not covered by this warranty.  

 

Negative head on the pressure side of any BW Solar submersible pump will void warranty of pump 
and motor. Pumps with a centrifugal pump end require a minimum positive head as specified in the 

product information sheets.  
Any alteration, damaging, removal, or other changes leaving the serial number or identification plate 
illegible or obscuring the identity and date of production of the product, will void this warranty.  
If product has been modified, remanufactured or tampered with in any way the claim will be rejected 

and sent back at the customer’s / Agents expense. (NO EXCEPTIONS)

 

 

Array Frames

 

 All Array frames, built or sold by BW Solar are compliant with current structural 

and loading ratings and are only to be used and installed as per instruction manuals provided. ANY 
alteration on design or installation voids all warranty. Any overloading of array structure and/or 
components are NOT covered under this warranty. 

 

3. Costs 

 

 All costs incurred in obtaining warranty are the responsibility of the customer or Agent, including but 

not limited to, shipping and handling, travel expense, lost time, lost production, or pickup and 
delivery and return shipment. 
 

4. Agents Responsibility 

 

•The Agent must supply their customer with all documentation relating to installation and warranty 

and, if installing, must complete and submit the SYSTEM REPORT FORM on behalf of their customer.  

•The Agent shall maintain a sufficient inventory of repl

acement parts to promptly satisfy their after 

sales service and customer needs. 

•The Agent is responsible for any warranty requirements of their customers.

 

•The Agent must not make any unauthorized modifications or alterations to the product.

 

•The Agent ma

y not make any warranties on behalf of BW Solar which have not been authorized in 

writing. 
 

5. Validity 

 

This limited warranty shall be valid from 1 September 2015 and shall apply to the above mentioned 
BW Solar Products sold to the Customer or Agent from this date, replacing and making void all 
previous warranties issued by BW Solar. 
 

 
  

 

   

 

 

Summary of Contents for MAXI ARRAY





















Reviews: