background image

 

 

INTRODUCTION 

 
 

Congratulations on your purchase of a winch.  We design and build winches to strict 

specifications  and  with  proper  use  and  maintenance  should  bring  you  years  of 

satisfying service.  

 

WARNING

 - 

Read, study and follow all instructions before operating this 

device.    Failure  to  heed  these  instructions  may  result  in  personal  injury 

and/or property damage. 

 

Your  winch  can  develop  tremendous  pulling  forces  and  if  used  unsafely  or 

improperly could result in property damage, serious injury or death.  Throughout 

this manual you will find the following symbols for caution, warning and danger.  

Pay  particular  attention  to  the  notes  preceded  by  these  symbols  as  they  are 

written for your safety. Ultimately, safe operation of this device rests with you, the 

operator. 

 

Indicates a potentially hazardous situation which, if not avoided, may result in 
minor or moderate injury.  This  notation is also used to alert against unsafe 
practices. 

 
 

Indicates a potentially hazardous situation which, if not avoided 
could result in death or serious injury. 
 

 
 
 
 
 
 
 
 
 
 
 
 

 

CAUTION

 

 

WARNING

 

Summary of Contents for 9500HS


















Reviews: