background image

Warner Electric • 800-825-9050

P-0257-WE • 819-9027 

  

7

Figure 5. Terminal strip label orientation

MCS-605-1 Sensing Potentiometer

  1.  Using a No. 2 drill, drill a 1/2” deep hole in 

the center of the dancer pivot shaft.

  2.  Drive the supplied pin into the hole in the 

shaft until half its length remains exposed.

  3.  Assemble the two brackets supplied with 

the two 10-32 screws.

  4.  Mount the sensor to the brackets using the 

three 8-32 screws.

  5.  Position the sensor and bracket so that 

the sensor shaft and pin are aligned and 
separated by 5/16”.

  6.  While holding the sensor and bracket in this 

position, mark the centers of the bracket 
holes on the machine. 

  7.  Drill and tap three (3) holes for 8-32 screws 

in the machine.

  8.  Connect the sensor shaft to the pin with the 

supplied universal coupling. The index mark 
on the sensor shaft must be aligned with 
the index mark on the sensor face when 
the dancer arm is at the midpoint position.

  9.  Mount the sensor and bracket to the 

machine with three (3) 8-32 screws.

  10. The sensor is now ready to be wired. Refer 

to the wiring section starting on page 8 of 
this manual for complete instructions. 

Figure 6. MCS-605-1 & TCS-605-5 Mounting Details

Summary of Contents for MCS-204

























Reviews: