background image

Making Electrical Provision for the Heater

Warranty

WARMUP 30-YEAR WARRANTY

Models:

USDW heaters and USDW-M heaters sold by Warmup, Inc.

THE WARMUP 30-YEAR WARRANTY DOES NOT EXTEND TO THERMOSTATS, WHICH ARE COVERED BY A
ONE-YEAR GUARANTEE FROM THE DATE OF ORIGINAL PURCHASE.

GOVERNING LAW.  Unless otherwise governed by applicable state law, this warranty shall be interpreted and enforced in
accordance with the laws of the State of Connecticut.

This 30-Year Warranty applies:

1. Only to the original homeowner(s) from the date of purchase

2. Only if the unit is registered with Warmup within thirty (30) days after purchase.  Filling out the card accompanying
this warranty in its entirety will complete registration.  In the event of a claim, proof of purchase is required, i.e.:
invoice and receipt.  Such invoice and receipt should state the exact model that was purchased; and

3. Only for the duration of the Lifetime of the floor covering under which it was originally installed if the purchaser of the
heater remains the owner of the residence in which it is installed. If the original purchaser sells such residence, the
warranty will transfer and continue for the duration of  the 30 years from date of purchase. 

4. Only if the heater has been grounded and protected by a GROUND FAULT CIRCUIT INTERRUPTOR (GFCI) at all times.

COVERAGE

1) The warranty period begins on the date of purchase.  Registration is effective only when a letter of confirmation is sent
by Warmup, Inc.

2) Warmup’s Undertile Heater is guaranteed by WARMUP, INC. (“Warmup”) to be free from defects in materials and
workmanship under normal use and maintenance for thirty (30) years, provided the Product is installed in accordance with
the accompanying Warmup installation manual, any special written design or installation guidelines by Warmup, Inc. for a
particular project, the National Electrical Code (NEC) and all applicable local building and electrical codes; and

3) Provided Warmup heaters are installed under ceramic tile, marble and natural stone surfaces.

4) During the period of Warranty, Warmup will arrange for the heater to be repaired or (at its discretion) have parts
replaced free of charge.  The costs of repair or replacements are your only remedy under this Warranty.  Such cost does not
extend to any cost other than direct cost of repair or replacement by Warmup and does not extend to costs of relaying,
replacing or repairing any floor covering or floor.

5) If Warmup, Inc. determines the repair of the product is not feasible; we will replace the product with equal or similar
features and functionality at Warmup’s sole discretion.  WARMUP’S MAXIMUM LIABILITY IS LIMITED TO THE ORIGINAL
PURCHASE PRICE OF THE HEATER MULTIPLIED BY THE PERCENTAGE OF THE WARRANTY PERIOD REMAINING.

SAFETYNET GUARANTEE GUIDELINES

1. Purchase a Warmup Undertile Heating Kit, and follow all recommended installation procedures in the Installation
Manual. Failure to follow the instructions will invalidate the guarantee. 
2. If you make a mistake and cut or damage the new heating before tiling, return the damaged heater to Warmup
within 30 DAYS along with your original dated sales receipt. WARMUP WILL REPLACE ANY PRE-TILED HEATER
(MAXIMUM 1 HEATER) WITH ANOTHER HEATER OF THE SAME MAKE AND MODEL – FREE. 

3. If you cut or damage the new heating during or after tiling, contact Warmup immediately for technical support.
Warmup will mail a repair kit and instructions at no charge to the installation site within 24 hours. Limit of one free
repair kit per customer or installer. 

Please note : 

(i) Repaired heaters carry a 5 year warranty only. Under no circumstances is Warmup responsible for the repair 
or replacement of any tiles which may be removed or damaged in order to affect the repair.

(ii) The Safety Net Guarantee does not cover any other type of damage, misuse, or improper installation 
due to improper adhesive or subfloor conditions. Limit of one free replacement heater per customer or installer.

24

Summary of Contents for USDW360





























Reviews: