background image

15 September 2017

 

 

All Dimension are in mm………….Copyright © 

 

1

 

Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification.

 

Warmington Tasman 46L & 70L Fires

 

 

Visit 

www.warmington.co.nz 

for Spec’s, DWG’s and PDF uploads of Fires

 

 

Fire, Flue System and Instructions to Comply with ASNZS 2918:2001

 

 

Keep these Instructions for further reference……Ensure that you have the correct and current Installation details for the Warmington Fire

 

 

Installation

 

The Warmington unit is to be Installed by a Certified Warmington Installer or a Certified NZHHA SFAIT Installation Technician .

 

See www.warmington.co.nz/members for a Certified NZHHA SFAIT Installer in your area .

 

 

CLEARANCES TO COMBUSTIBLE SURFACES UNLESS STATED

 

 

IMPORTANT 

Read all the instructions carefully before commencing the Installation. Failure to follow these instructions may result in a fire hazard and void the warranty 

Freestanding Fires - Clean Air Approved Wood Burner

 

Installation Instructions

 

ADD Cowl

 

Flashing Cone

 

Galv Combo Liner

 

Ceiling

 

Flue

 

Warmington

 

Double Flue

 

Shield

 

Floor Protector

 

Summary of Contents for Tasman 46L Fire













Reviews: