background image

 

 

 

 

TECHNICAL, SPARES & GUARANTEE CLAIMS 

For technical advice about the installation, use and servicing of this appliance, please contact the 

Warmflow Customer Care Centre. Please also refer to our website www.warmflow.co.uk. 
Should replacement components be required, a list of available spares is provided in Section 4.2, 

page 7. Only Warmflow spare parts must be used with this product. 
In the unlikely event that replacement components might be required within the guarantee period, 

please notify the Customer Care Centre stating the serial number of the appliance, the nature of 

the fault and the part number of the replacement components required. 

 

 

For Parts, Service, Technical & Customer Care 

Great Britain & N. Ireland:  028 9262 1515 
Republic of Ireland:  

048 9262 1515

 

 
HEAD OFFICE 

 

 

 

 

 

GB OFFICE 

Lissue Industrial Estate, Moira Road,  

Unit C4, Stafford Park 4, 

Lisburn, Co. Antrim, N. Ireland, BT28 2RF 

Telford, TF3 3BA 

Tel:

 

(028) 9262 1515 

Tel:

 

(01952) 607 750 

Fax:

 

(028) 9262 0869 

Fax:

 

(01952) 603 983 

E-mail:

 

[email protected] 

E-mail:

  [email protected] 

 

[email protected] 

[email protected] 

 

[email protected] 

[email protected] 

 

WEBSITE 

www.warmflow.co.uk

 

 

 

Summary of Contents for Nero BT110

















Reviews: