background image

2

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should 
always be taken, including the following:

 1. 

READ ALL INSTRUCTIONS.

 2. 

 Unplug from outlet when not in use, before putting  
on or taking off parts, and before cleaning.

 3. 

  

To protect against electrical hazards, do not immerse the 
blender base in water or other liquids.

 4.  

 This appliance is not intended for use by persons (including 
children) with reduced physical, sensory or mental 
capabilities, or lack of experience and knowledge, unless 
they have been given supervision or instruction concerning 
use of the appliance by a person responsible for their safety.

 5.  

Children should be supervised to ensure that they  
do not play with the appliance.

  6.  Avoid contact with moving parts.

 7.  

Do not operate any appliance with a damaged cord or 
plug or after the appliance malfunctions or is dropped or 
damaged in any manner. Return appliance to the 
nearest authorized service facility for examination, repair or 
electrical or mechanical adjustment.

 8.   

The use of attachments not recommended by the appliance 
manufacturer may cause hazards.

  9.  Do not use outdoors.

 10.   Do not let cord hang over edge of table or counter, where it 

can inadvertently be pulled on or tripped over or touch hot 
surfaces, which could damage the cord.

 11.   Keep hands and utensils out of container while blending 

to prevent the possibility of severe personal injury and/or 
damage to the blender. A rubber scraper may be used, but 
must be used only when the blender is not running.

 12.  Blades are sharp. Handle carefully.

 13.   Never place cutting assembly or cutting blades on base 

without container properly attached.

 14.  Always operate blender with cover in place.

 15.  Always operate blender with jar pad in place.

 16. 

 CAUTION:

 This blender is not intended for use with hot 

liquids or ingredients.

www.calcert.com

[email protected]

1.888.610.7664

0

5

10

15

20

25

30

Summary of Contents for Torq 2.0 TBB Series













Reviews: