6
7
IMPORTANT – HOT BLENDING INSTRUCTIONS
To minimize the possibility of being scalded when blending hot materials,
the following precautions and procedure must be observed.
• Hot materials are those that are 100
°
F (38
°
C) or hotter.
• Limit the amount of materials processed to 1 pint.
• Completely remove the center portion of the two-piece container lid
before starting motor (this will allow venting of the rapidly heated and
expanding air inside the container when blender is running).
• Always start blending on lowest speed setting, and then progress to
desired speed.
• Never stand directly over blender when it is being started or while it
is running.
CLEANING AND SANITIZING INSTRUCTIONS
THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH USE
OF THE BLENDER ACCORDING TO THE FOLLOWING INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUES OF PROCESSED MATERIAL
TO COLLECT ON THE INTERNAL SEALS OF THE BLADE ASSEMBLY,
RENDERING THEM INEFFECTIVE.
•
Wash, rinse, sanitize and dry container prior to initial use and whenever it
will not be used again within a period of 1 hour.
•
Wash and rinse container after each use.
•
Clean and sanitize motor base prior to initial use and after each use.
•
Washing solutions based on non-sudsing detergents and chlorine-based
sanitizing solutions having a minimum chlorine concentration of 100 PPM
are recommended.
The following washing, rinsing, and sanitizing solutions, or their equivalents,
may be used.
SOLUTION
PRODUCT
DILUTION IN WATER TEMPERATURE
Washing
Diversey Wyandotte
4 tablespoons
Hot 115˚F (46˚C)
Diversol BX/a or CX/A
/gallon
Rinsing
Plain Water
Warm 95˚F (35˚C)
Sanitizing
Clorox
®
1 tablespoon/gallon
Cold 50-70˚F
Institutional Bleach
(10-21˚C)
•
In repetitive batch-processing applications, frequent cleaning of the
container will prolong the life of the blade assembly. In no case should
actual running time between cleanings exceed one-half hour.
•
Do not use container to store processed foods or beverages.
TO WASH AND RINSE CONTAINER
1. REMOVE CONTAINER FROM MOTOR BASE. Remove lid. Rinse
container interior and lid under running water. Add washing solution to
container. Scrub and flush out the container interior and lid to dislodge
and remove as much food residue as possible. Empty container.
2. Wipe down exterior of container with a soft cloth or sponge dampened
with washing solution. Wash lid and lid insert in fresh washing solution.
Fill container one-quarter full with fresh washing solution, cover (with lid
only), place on motor base and run on high speed for two (2) minutes.
Empty container.
3. Repeat step (2) using clean rinse water in place of washing solution.
IMPORTANT
NOTE: IN ORDER TO MINIMIZE POSSIBILITY OF SCALDING,
TEMPERATURE OF WASHING SOLUTION AND RINSE WATER MUST
NOT EXCEED 115˚F (46˚C), AND QUANTITY USED MUST NOT EXCEED
ONE-QUARTER CONTAINER FULL.
IF HIGHER TEMPERATURES OR LARGER QUANTITIES ARE USED,
OBSERVE ALL PRECAUTIONS GIVEN IN THE OPERATING MANUAL UNDER
“HOT BLENDING INSTRUCTIONS”, page 6.
TO SANITIZE AND DRY CONTAINER
1. Wipe down exterior of container with a soft cloth or sponge dampened
with sanitizing solution.
2. Fill container with sanitizing solution, cover, place on motor base, and
run on high speed for one (1) minute. Empty container. Dislodge any
residual moisture from blade assembly by placing empty container on
motor base and running on high speed for two (2) seconds.
3. Sanitize lid and lid insert by immersing in sanitizing solution for two
(2) minutes.
4. Do not rinse container, lid, or lid insert after sanitizing is completed.
Allow parts to air dry.
TO CLEAN AND SANITIZE MOTOR BASE
1. UNPLUG POWER CORD. Wipe down exterior surfaces of motor base
with soft cloths or sponges dampened with washing solution, rinse
water, and sanitizing solution. Prevent liquid from running into motor
base by wringing all excess moisture from cloths or sponges before
using them.
DO NOT IMMERSE MOTOR BASE IN WASHING SOLUTION, RINSE WATER
OR SANITIZING SOLUTION.
2. Allow motor base to air dry before using.
Any other servicing should be performed by an authorized
service representative.
SERVICE
Refer to the list of Authorized Service Centers enclosed with your Waring
®
Commercial Blender for the name of the nearest Service Center, or
write to:
Waring Factory Service Center
314 Ella T. Grasso Avenue
Torrington, CT 06790
(800) 492-7464
Ship blenders for repair to the above address or to an Authorized Service
Center. Do not ship to a Waring Sales Office.
Note: If your application involves the processing of biologically active
material, we request that any items returned for service be sterilized
before being shipped. Such items must be clearly identified as having
