WANHAO GADOSO REVOLUTION 2 User Manual Download Page 6

Page: 6 / 51

SAFETY INSTRUCTIONS

Before you get started, please read these safety instructions.

CAUTION

: WANHAO 3D Printers include moving parts that can cause injury. Never reach inside

the WANHAO 3D Printer while it is in operation, and allow time for the printer to cool down after

operation.

MOVING PARTS

Do not leave the WANHAO 3D Printer unattended during operation.

Always wear gloves while handling resin or printed objects.

Always be careful when using the scraper. Never direct the scraper towards your fingers.

In case of emergency turn off the 3D printer by unplugging the power outlet.

• The printer must not be exposed to water or rain, or the printer will be damaged.

• The printer is designed to be used in ambient temperatures, ranging from 15°C to 30°C.

• The printer is designed to be used in humidity levels ranging from 20% to 50%.

• Operating the printer outside the recommended temperatures and humidity levels

may result in low quality print models.

• Eye protection during cleaning or sanding of the printed models is recommended

to protect your eyes from small airborne particles.

Summary of Contents for GADOSO REVOLUTION 2




















































Search results

Summary of Contents for GADOSO REVOLUTION 2

Reviews:

Related manuals for GADOSO REVOLUTION 2

Brands by name

Popular brands

WANHAO GADOSO REVOLUTION 2, User Manual

Search results

Summary of Contents for GADOSO REVOLUTION 2

Reviews:

Related manuals for GADOSO REVOLUTION 2

Brands by name

Popular brands