background image

39

W&T

 

Digital-I/O Extender Sets

Subject to error and alteration

Technical Data

Transmitted signals: 

2x Digital In, 2x Digital Out 

Digital-I/O connector:  6-pin plug-in screw terminal 
Digital outputs: 

2 outputs, 6V-30V, 0.5A,  

 

Short circuit protected 

Digital inputs: 

2 inputs acc. to IEC61131-2, type 3 

Input voltage: 

max. 30V 

Signal delay: 

Input to output: max. 250µs 

 
Glass fiber connector:  ST connectors (SMA on request) 
Fiber medium: 

Duplex multimode glass fiber cable 

Transmitter type: 

LED 

Wavelength: 

820 nm 

Optical budget: 

50/125µm: typ. 9.6dB, min. 4,2dB 

 

62.5/125µm: typ. 13.4dB, min. 8.0dB 

Maximum distance: 

50/125µm:  

 

typ. 3200m, min. 1400m @3dB/km 

 62.5/125µm: 

 

 

typ. 3800m, min. 2200m @3.5dB/km

Supply voltage: 

12..24 V AC/DC 

Current draw: 

max. 150 mA at 12 V DC 

Isolation: 

min. 1 KV between digital-I/O 

 

and supply voltage 

 
Temperature range: 

Storage: -40..+70°C 

 

Operating: 0..+60°C  

Humidity range: 

5..90% rH (non condensing) 

Life expectancy:  

> 25 years (@25°C ambient temp.)

Housing: 

Plastic housing for DIN rail mount  

Dimensions: 

105x75x22,5 mm 

Weight: 

approx. 250 g 

Scope of delivery: 

1x Digital-I/O Extender Set 2x2 

 

Multimode ST

Summary of Contents for 17633





























Reviews: