background image

25

Installation, Servicing and User Instructions   |   EN

M.  Replace Grate

N.  Replace the Firebed arrangements

O.  Replace Window Assembly and Trims

P.  Check the fl ue system and terminal, making sure that the terminal vent is fully clear

Q.  Light the appliance and test setting pressures

R.  Check the safe operation of the appliance.

4.1 Cleaning the Ceramics

Remove the ceramics as detailed in A - E above.

Gently clean the ceramics in the open air, using a soft brush and a vacuum cleaner. Where necessary replace 

damaged components only with genuine Wanders specifi ed parts. Seal any scrap ceramics in plastic bags and 

dispose at proper refuse sites. When using a vacuum cleaner, it is recommended that one with a HEPA fi ltering 

system is used.

Re-fi t the Firebed arrangement, re-seal the appliance and check the safe operation of the appliance.

4.2 Servicing the Burners

Remove the Burner Top Assemblies as detailed in A - H above.

The pilot is now clearly visible, the pilot, including the Thermocouple, can be replaced/serviced by removing 

raising the pilot assembly from its mounting. This is done by removing the two screws on the surface of the pilot. 

The fi ttings on the under-side of the pilot can be un-done using a 10mm spanner where appropriate.

To access the Main Burner Injectors, the Burner base units must be removed. This is done by removing the six 

bolts (M6, 10mm spanner) holding the burner in. With these six bolts removed, the Burner base can be raised up 

through the Firebox, and the Injectors can be easily accessed.

When replacing any parts use only original Wanders specifi ed parts.

4.3 Opening the Glass

•  Place the suction lifter on the middle of the glass. Make sure the glass is not hot.

•  Open the glass clamps with the enclosed hook.

•  Pull the glass slightly towards you.

•  Lift the glass slightly and pull to bottom towards you.

•  Put the glass aside carefully.

Terugplaatsen van de glasruit

•  Place the glass at the base of the mainburner. Make sure the area is clear of any media covering the burner.

•  Push the top of the glass in its place. Make sure the 2 steel tabs lock in the frame of the appliance.

•  Pull the glass clamps down to lock the glass.

•  Remove the suction lifter.

Summary of Contents for Lenga 500





































Reviews: