background image

 

1 Introduction 

 

 

Page 6 of 37

 

Operating Manual WLVCM-BA-10 

 

EN 

1.5  Warranty and Liability 

According to the conditions laid down by the German Engineering Federation (VDMA), Walther 

Systemtechnik GmbH has a guarantee of 12 months under normal European operating conditions on 

its own parts (spare parts are excluded); or according to the conditions of the manufacturer. 
This guarantee can only be granted by Walther Systemtechnik GmbH, if: 

  the user has thorough knowledge of the content of this operating manual; 

  the user follows the instructions and notes contained in this operating manual; 

  the user does not rebuild or make changes on parts of the device without prior consent of Walther 

Systemtechnik GmbH. 

1.6  Copyright 

We reserve the copyright for this operating manual. This operating manual is exclusively designated for 

the operator and his personnel. 

  Any copying – also only in part – or processing, or distribution or other use is strictly prohibited. 

1.7  List of Signs and Symbols 

Symbols are used indicate dangerous situations and specific behavior. These symbols are also used in 

this operating manual. All warning, danger and information symbols describe situations which can be 

harmful to persons, material or environment if rules are not followed. 
The operating manual uses the following signs and symbols for dangers. 

 

 

 

DANGER 

Symbol „Danger“

 

Signals a potentially dangerous situation..  

Death or severe injuries

 

can

 follow, if you do not avoid this situation. 

 

 

 

 

WARNING 

Symbol „Warning“

 

Signals a potentially dangerous situation. 

Death or severe injuries

 

can

 follow, if you do not avoid this situation. 

 

 

 

 

CAUTION 

Symbol „Caution“

 

Signals a potentially dangerous situation. 

Slight or minor injuries 

can

 follow, if you do not avoid this situation. This sign is also 

used where damage to property is possible. 

 

 

 

 

IMPORTANT 

Indicates tips for usage and other particularly useful information. 

No

 dangerous situation. 

 

 

 

Summary of Contents for 50008746






































Reviews: