background image

 

 

   

 

 

Revision 5 

15 

Product Manual  
WHBV-101W-LH-NB and WHBV-101W-RH-NB 

 

WARNING! The washbasin weighs approximately 35Kg. Always use safe lifting 
procedures when lifting heavy loads. Make sure the washbasin is correctly 
secured to the wall or correctly supported before working in the vicinity. 

 

NOTE: Make sure you do not abrade or damage water tubes & waste pipe when 
you insert them through the wall. 

 

5.5 Water and Waste Connections 

 

NOTE: The connection of the water supply and waste must be completed in 
accordance with the plumbing code AS/NZS 3500 
 
NOTE: Before you carry out the following steps, flush the water supply pipes to 
remove any debris and trapped air. 
 
NOTE: Fit a Y strainer in the water supply feed pipe before connection to the 
washbasin, especially on older installations where loose particles from ageing 
water pipes can cause a blockage.  
 
NOTE: Fit a service isolating tap on the water supply feed. This allows for ease 
of 

maintenance when required. The isolating tap is not supplied with the 

product and should be purchased separately. 

 
NOTE: Use of any pipe sealing compound should be avoided to prevent 
blockages & damage to the basin faucet. 

 
1.  Complete the connection of the water supply to the basin tap outlet. 

 

2.  Connect the waste pipe adapter to a deep seal waste trap. 

 

NOTE: The trap must be fitted at a lower height than the basin waste pipe for 
correct drainage. Fit an elbow connector to the waste pipe first before 
dropping down to the trap inlet connection. 
 
 
 
 
 
 

Summary of Contents for WHBV-101W-LH-NB




















Reviews: