background image

WX520 / WX520L / WX520T
Log Splitter

Operating Instructions

25

6.12 Emergency Stop

In the event of an emergency:

1. 

Move the splitter control to the neutral position.

2. 

Move the engine throttle control to the 

STOP

 position to 

turn off the engine and close the fuel shutoff valve.

3. 

Remove the cause of the emergency before starting the 
engine and resuming work.

6.13 Log Placement

 WARNING!

Risk of pinching or crushing hazard between the 

wedge or push block and the log! 
Never place hands at the ends of the log. 

Always grasp logs by the sides when loading or 

removing.

W035

•  Always grasp logs by the bark side and not the ends, 

when placing or removing logs from the splitter. 

Minimize 

the chance of getting fingers, hands or arms caught 
between the push block and the log.

• 

Any logs or debris remaining on the splitter bed should only 
be removed after it is safe to do so.

00645

Figure  12 – 

Correct log placement

6.14 Split Wood

 WARNING!

Risk of pinching or crushing hazard! The worker 

loading the splitter MUST be the only one in 

control of the hydraulic cylinder and splitting 

wedge. 
Only one worker should operate and load the 

wood splitter.

W036

IMPORTANT!  Do not hold the splitter-control lever to extend 
or retract the cylinder once it has reached the end of its 
stroke. Doing so can overheat the oil and could damage the 
engine.

1. 

Place wood or log on the splitter.

2. 

Push the control lever to the 

Extend

 position and hold to 

split wood.

3. 

Release the lever when the log splits or cylinder reaches full 
stroke and stops.

4. 

Pull the lever to the 

Retract

 position to retract the push 

block. The detent holds the lever until the cylinder fully 
retracts, allowing hands-free operation. 

5. 

If the log is large enough to require another split, reposition 
and repeat steps.

6. 

Pile the split wood close to the working area, but do not 
allow pieces to pile up and clutter the area. A cluttered 
working area can lead to tripping and an accident. 

02061

3

2

1

Figure  13 – 

Splitter-control valve

1.  Extend position
2.  Neutral position
3.  Retract position

Summary of Contents for WX520









































Reviews: