background image

INITIAL INSTALLATION AND START-UP TIPS 

WALLAS 85 DU & DP COOKTOP   

 

The 85 series Wallas cook-top is the third generation of cooking devices 
from this Finnish company.  Starting in 1995, Wallas introduced a #2 diesel 

fueled cook-top called the Model 95D, designed primarily for the North 
American market.  This model was manufactured through 2005.   

 

Though primarily intended for “recreational” use, many 95Ds were placed 
into  “commercial”  use,  with  reasonable  success,  and  most  units, 
recreational and commercial, are still in service today.  Most 95Ds sold 
here in North America were fitted with the model 25 blower lid, that 

combination of stove and lid was marketed as the 125D.  Early 25 lids had 
a wood veneer top, while the later 25E models had a tooled metal top. 

 

 

 
 
 
 

 

 
 

 
 

 

 
In 2006, the current Model 85 started into production.  This model grew out 

of the information received from nearly 10,000 Model 95D’s sold 
throughout the world.  Some of the major improvements in the model 85D 
over the model 95D include a dramatically strengthened “case” with a 
“bonded” ceramic surface, a highly refined PC board with internal hour 

meter, and super long life “brushless” motors for combustion and heating.   
 

As of 2011, over 8,000 of these 85D units have been sold and have proven 
to have a very robust design and a significantly longer service interval 
than the Model 95D.   Blower and combustion fan life is many times that of 
the 95D. 
 

85DU w/270 Lid 

85DP w/270 Lid 

Summary of Contents for 85DU w/270 Lid








Reviews: