background image

15 

Weekly Cleaning 

NOTE: 

• 

If the pasta cooker usage is very high, we recommend that the weekly cleaning  
procedure is carried out on a more frequent basis. 

• 

Ensure that protective gloves are worn during the cleaning process. 

• 

DO NOT use harsh abrasive detergents, strong solvents, sharp scrapers or caustic  
detergents as they will damage the surface of the pasta cooker. 

• 

Ensure that the water circuit is free of ferrous particles.  Any such particles deposited 
in the bottom of the tank may cause it to rust. 

 

Thoroughly clean the interior and exterior of the pasta cooker regularly.  Do not use wire brushes on the 

pan.  Clean using a mild detergent and a hot water solution using soft cloth or a soft bristled brush.  Dry 

the appliance thoroughly using a dry clean cloth. 

 

NOTE:  In order to prevent the forming of rust on the steel components, ensure that the detergent 

or cleaning material has been entirely removed after each cleaning process. 

 

Stainless Steel Surfaces 

a.  Clean the interior and exterior surfaces of the pasta cooker with hot water, a mild detergent  

solution and a soft scrubbing brush.  Note that the gas control knobs are a push fit onto the gas 

and water control valve spindles and can be removed to allow cleaning of the front of the control 

panel. 

b.  Baked on deposits or discolouration may require a good quality stainless steel cleaner or stainless 

steel wool.  Always apply cleaner when the appliance is cold and rub in the direction of the grain. 

c.  Dry all components thoroughly with a dry cloth and polish with a soft dry cloth. 
 

Periodic Maintenance 

NOTE:  All maintenance operations should only be carried out by a qualified service person. 
 

To achieve the best results cleaning must be regular and thorough and all controls and mechanical parts 

should be checked and adjusted periodically by a qualified service person.  If any small faults occur, have 
them attended to promptly.  Don't wait until they cause a complete breakdown.  It is recommended that 

the appliance is serviced every 6 months. 
 
If the appliance is not used for long periods, close the gas shut-off valve upstream of the appliance and 

clean the appliance thoroughly. 
 
The appliance should be inspected and the gas exhaust flue cleaned by an authorized service person at 

least every 6 months. 

Cleaning and Maintenance

 

WARNING: 

 

DO NOT ATTEMPT TO MOVE THE PASTA COOKER WHILST THE COOKER IS FULL OF WATER. 

 

BEFORE ATTEMPTING TO MOVE THE PASTA COOKER, ENSURE THAT ALL THE WATER HAS 

BEEN DRAINED FROM THE TANK.  REFER TO THE INFORMATION ON THE PREVIOUS PAGE 

ON HOW TO DRAIN THE WATER FROM THE PASTA COOKER. 

Summary of Contents for PC8140G


























Reviews: